Why the burner on a gas stove does not work: instructions for repairing and replacing the burner

There may be several answers to the question why a gas stove smokes. The main sign of such a malfunction is the appearance of black carbon deposits on the dishes. If the color of the flame has ceased to be blue and has become yellow-red, it is worth inspecting the equipment and cleaning it. You may need to replace some gas stove parts or perform other maintenance. In this article we will look at the main causes of soot and methods to correct this problem.

Soot formation on dishes

A change in flame color indicates instability of the burners. Insufficient air supply or incomplete combustion of fuel will certainly lead to the formation of soot.

Additional Information

It is not prohibited to use classic household methods, such as soda, vinegar, citric acid or alcohol.

To clean a gas oven, you can use store-bought and folk cleaning products.

Use a regular foam sponge, or a soft washcloth or cloth. Apply products only with a creamy consistency, distributing them evenly over the enamel. To completely remove adhered grease and stains, leave for 1-2 hours so that the product removes all dirt and germs from the surface of the gas stove. Next, remove the burners and soak them together with the cleaning agent in water for 1-2 hours.

Afterwards, rinse everything off with a damp sponge, wipe with a cloth and replace the dry burners.

Please note: Follow safety precautions when using the stove and do not panic if you smell gas. Just turn off the gas pipe valve and try not to stay in the apartment until specialists arrive

Adviсe:

Do not turn the gas knobs to full power, as if the gas supply is too powerful, the flame may come off the burner, thereby releasing carbon monoxide into the air. Do not leave a switched on gas stove unattended. Monitor the quality of the equipment; if you see a yellow flame, the oven in the gas stove does not burn, or any other problems arise, call specialists in a timely manner. Do not allow liquid to splash onto the surface of the stove, as this may extinguish the fire and cause a gas leak. Check your gas water heater. Pay attention to whether the hood is working. It is very simple to determine this; you need to bring a burning match to the chimney, hold it for a while, if the flame is drawn in, it means the hood is working properly

If the flame burns as usual or deviates to the side, then the water heater cannot be used.

It is necessary to periodically monitor the operation of the oven.

Why clean a gas burner?

Many of you have probably encountered a situation where the gas from the stove burners begins to burn worse. The burner flame partially or completely disappears, changes its color and shade; in particularly advanced cases, one or more burners may not work at all.

Sometimes the problem lies in weak gas pressure. But most often the cause of such troubles is the usual contamination of the burner dividers or nozzles that are located under the burner. During cooking, liquid or food particles may get into small holes. Contamination can also occur due to the frequent use of powdered cleaning agents to clean the surface of the stove. In any case, if a problem arises, you should try to solve it.

Safety rules for stove repairs

When inspecting and repairing the stove, you must follow simple safety rules - turn off the fuel supply, turn off the electrical power, and children and animals should not be left in the room. Upon completion of work, you should make sure that the burners are burning evenly and that the connection between the stove and the gas pipeline is tight.

In the event of a serious breakdown, it is undesirable to carry out repairs yourself, without the appropriate experience. In this case, it is better to call a specialist from an organization with which an agreement has been concluded for servicing gas equipment.

For unauthorized interference in the gas supply system, liability is provided for, specified in Article 9.23 of the Code of Administrative Offences. The fine will range from 10 to 30 thousand rubles.

If a fire or explosion occurs due to the fault of the owner of the equipment, charges will be brought against him, in accordance with paragraph 6 of part 3 of Article 158 of the Criminal Code of the Russian Federation. The amount of penalties for illegal actions: from 100 to 500 thousand rubles. Punishment for this offense is also provided in the form of imprisonment for a term of up to six years or forced labor for a term of up to 5 years.

Finding out the causes of the problem

If a burner on a gas stove does not burn well or does not ignite, you must first disconnect the equipment from gas and electricity. Inspection and repair of the hob may only be carried out after shutting off the gas fuel supply.

Basic security measures cannot be neglected here.

Whether or not the smell of gas is felt in the kitchen after the burner goes out does not matter; any manipulations to maintain gas equipment should be performed only with open windows and good natural ventilation of the room

Many modern gas stoves are equipped with electronics and automatic ignition systems that require electrical power. Often, inexperienced home craftsmen, when working with a gas hob, forget about this feature of this device. As a result, methane vapors ignite from sparks. Therefore, before starting repairs, it is recommended to disconnect not only the stove itself, but also all electrical appliances in the kitchen.

Problems with gas stove burners arise due to:

incorrect operation of the solenoid valve and/or thermocouple;
nozzles clogged with grease and soot;
faulty spark plugs;
long breaks in servicing gas equipment.

Owners of private houses and apartments where there is a gas stove are required to enter into an agreement for regular inspection of the equipment in question with a specialized organization. Without such an agreement, gas will not be supplied to the consumer.

And gas workers should come at least once a year, checking the functionality of the hob and, if necessary, immediately repairing it. All other calls are paid separately.

If problems with the stove arose during the period between routine checks, you will either have to call a technician again or carry out the repair yourself

Moreover, if during self-repair of burners and other hob devices they are damaged, then it is prohibited to turn on the faulty device without the gas technicians. Even if the stove is more or less operational, then during an annual inspection a gas company specialist will identify a breakdown and immediately shut off the gas until the defects are eliminated. And these are inevitable additional expenses. Plus, they may also impose a fine.

It is recommended to undertake repair of a gas stove with your own hands only if you are absolutely sure that you will do everything correctly

There are no particular difficulties in this work, but you can break something through carelessness or ignorance

The problems are the following:

The flame is not blue in color - there is not enough oxygen or too much gas is supplied to the injector.
The burner does not light - the spray holes are clogged with soot or the thermocouple or spark plug is faulty.
The fire goes out - the gas supply is cut off due to a faulty gas control or problems with the gas pipe.

You can clean or replace the burner on your gas stove yourself. But if the problem area is the meter, the gas pipe itself (cylinder) or an external gas sensor, then it is better to refuse arbitrariness.

In such a situation, you should seek help from the gas workers responsible for the serviceability of the VKGO and VDGO.

If you have a faulty electric ignition

Almost all devices are now equipped with it, which has a positive effect on ease of use. Let's first define how electric ignition works and works.

Electric ignition consists of four parts:

transformer (unit) operating from a 220 V electrical network;
electrical wire leading from the transformer to the ignition mechanism;
ceramic candle;
ignition button located on the control panel, next to the rotary switches.

The mechanism of electric ignition is as follows:

When you press the button, the circuit closes;
The transformer generates the current for the spark;
The pulse is supplied through the wires to the gas burner;
The ceramic candle produces a spark and the burner ignites.

It is noteworthy that the candle fires on all burners without exception, however, only the one that receives gas is ignited.

It is very important to ensure that the network always has one voltage - 220 V. To protect your stove, you can buy a household voltage stabilizer, which will protect you from unexpected current surges

Otherwise, short circuits and unstable operation of the network negatively affect the electric ignition and can cause breakdown. If your hob exhibits the following malfunctions, then the problem is with the ignition:

you turn on the button, but the ignition does not work;
one or all spark plugs spark;
you release the button, and the ignition works.

You turn on the button, but the ignition does not work

The first and most common reason is contamination of the mechanism button and/or burner with dirt and combustion waste. Cooking food entails splashing fat and food all over the stove, so this problem is not uncommon. Clean the ignition button, wipe the burner, clean the nozzle with a needle or any other thin stick, wait until everything is dry.

One or all spark plugs are sparking

If the spark plugs on all burners sparkle orange or yellow and operate intermittently, then the problem may be a faulty electric ignition unit. It needs to be replaced, but doing it yourself is extremely difficult. The block is located in the middle of the panel; it needs to be disassembled and the contacts disconnected, so it is better to trust professionals in this situation. To be sure that the problem is in the transformer, do the following:

in the dark, with the lights off, turn on the ignition button;
if a spark appears on all burners of the color described above (yellow, orange), the unit definitely requires replacement;
if the spark is blue, the unit is working.

If the integrity of the spark plug is damaged or its rod is oxidized, it will spark orange or yellow intermittently. This is solved by replacing the faulty spark plug. However, such problems are quite rare and this is due to the design of the candle itself. It is a steel wire, one millimeter thick, encased in porcelain. For a candle to become unusable, it must be in very unfavorable conditions of high humidity or subject to shock.

You release the button, but the ignition works

This may be due to a faulty transformer or oxidation of the contacts.

When washing the panel or boiling water, liquid can penetrate into the middle of the device, onto the contacts. With constant leaks and heat coming from the burners turned on, the contacts oxidize. They become rough, they can stick together and break. Their technical cleaning and high-quality drying will help.

The stove smells strongly of gas: reasons

The gas itself is odorless, but for safe operation a special chemical additive is added to its composition, which creates a familiar specific aroma.

When the gas burner is turned on, a small amount of gas enters the room, causing a short-term false illusion of a leak. This is absolutely normal, there is no need to worry. But if a constant smell of gas is observed when the hob is turned off or running, then it is necessary to immediately find out the reason for this and eliminate the malfunction.

The smell of gas can occur in two situations:

when the stove is turned off;
only when the stove is running.

It is necessary to look for a breakdown in these two cases in different ways.

If you notice a smell when the gas panel is turned off

Such leaks are associated with a violation of the tightness in the components of the gas hob.

This may be due to:

loosening the hose connection nut;
cracks in the hose itself or in the gasket;
the rubber seal on the connection has become loose;
improper installation of the hob;
The gas valve needs replacing.

In order to accurately verify the location of a gas leak, use a simple method - a soap solution. The procedure is performed like this:

dilute dishwashing detergent or any other foaming liquid in a small amount of water, whisk;
turn off the power to the stove (if you have electric ignition);
Use a shaving brush to lubricate all hoses, pipe connections, and threads;
if you observe bubbles, this indicates a gas leak in a specific place; if there are no bubbles, the problem is not in the internal filling.

If there is a leak, then subsequent repairs depend on its location. A broken hose is completely replaced. If this is a threaded connection, then the problem is the aged sealant. We unscrew the thread, clean it, apply new sealant or winding, and reassemble it. The same algorithm of actions applies if there is a crack in the gasket at the junction: it will require replacement.

If nothing is found during the soap solution test, inspect the gas valve. Its repair (replacement) is the responsibility of the gas service or a similar organization responsible for the area where you live. If you have the slightest doubt about your own competence in this matter, we strongly recommend inviting a specialist.

You can repair the gas valve yourself if:

you have enough experience in plumbing work, you have already had to deal with a similar replacement;
the pipe in front of the valve is intact, there is no corrosion;
you know where and how your apartment is de-energized;
All necessary tools are available.

Remember: when working independently, gas leaks cannot be avoided! To do this, turn off the power to the entire room and open the windows wide.

If the gas is released only when the device is turned on

In this case, there may be two reasons:

flame too big. Adjust it and everything will be fine;
leakage occurs only in those parts of the gas pipeline that are activated when the stove is turned on - the nozzles, the places where the tubes exit from the taps to the nozzles, the places where the tubes connect to the nozzles.

You can check the last option using a soap solution that is already familiar to us. After turning off the power to the gas panel, remove the burners and remove the stove cover. Replace the gas burners and carefully wipe all mentioned areas with soapy water and turn off the gas. Bubbling will definitely indicate a leak.

At the nozzle installation site, a leak may be due to a weak tightening or a defective sealing washer. Easy to fix - tighten the nozzle, replace the washer

These operations must be done carefully so as not to strip the threads of the parts.

If there is a leak in the places where the pipes are attached, then most likely it is due to the unsuitability of the rubber sealing rings. They require replacement. It is produced in this way:

the bracket is disconnected (if there is one);
the tube is pulled out;
the ring is removed and a new one is installed;
the tube is inserted into the designated place;
the bracket is put on.

If there is a lot of fat: how to wash a gas stove

For the highest quality cleaning and removal of all contaminants, it is necessary to carry out preliminary preparation.

Sprinkle baking soda onto a damp surface in an even layer and let it sit for 30-40 minutes. This method is not complicated and makes it possible to clean the stove and oven. The oven can also be cleaned this way.

If there is too much grease, then it is better to apply a cleaning agent on it and leave it for a while, and then wipe it off

After waiting time, you can start cleaning; water and baking soda must be removed from the surface of the stove using a soft sponge.

In no case should steel wool be used when cleaning the stove and oven, as they can cause damage to the surface, but it is better to use a sponge and a toothbrush or cotton swabs, but this is in the most difficult to reach places.

To clean the grate on a gas stove, you must use the soap solution described above. Citric acid or juice and vinegar are also excellent auxiliaries. They can be used in place or separately. Ammonia and vinegar can remove dried and burnt-on stains on the surface of a kitchen gas stove.

All gas stoves are equipped with removable handles.

The main thing here is not to rush, but to act carefully, without rushing and without breaking the plastic.

Stoves from different manufacturers certainly differ from each other. However, as experience shows, most design solutions from different manufacturers are VERY, VERY similar.

Before starting work, turn off the gas supply using the shut-off valve.

Gas stove Hephaestus, Indesit, Electrolux, Darina (knobs that need to be pressed and turned when igniting).

Just pull it towards you, along with the ring on which the symbols are drawn.

If you have any difficulties, try treating it with WD-40. Then, inserting one knife into the gap between the ring and the handle itself, bend it a little. And on the opposite side, use a second knife, acting as a lever.

If it doesn’t go through the cloth, use pliers carefully.

Then soak the hands in water with the addition of fairy. After a while, the fat will turn white and be wiped off with a toothbrush.

How to lubricate the tight rotating mechanisms of the crane?

Factory lubrication of the faucet is designed to last approximately five years. In Soviet times, gas workers used graphite lubricant (called NK-50), LG-Gaz41, LS-1P.

Graphite (crushed carbon), which forms the basis of the lubricant, is able to fill microscopic irregularities in parts, while reducing friction.

It has great refractoriness and does not dry out for a long time.

You can use solid oil or technical petroleum jelly.

Tips for repairing gas stoves with your own hands

How to properly clean the surface and parts of the burner?

This procedure can be carried out in several ways. Use one of the options below so as not to waste a lot of time and do everything right.

Method 1

Check if the stove has cooled down.
Remove the burners from it.
Disconnect the divider.
Clean the holes of the divider with a needle or thin knitting needle.
Take a bowl or small container.
Fill it with hot water and detergent in a ratio of approximately 10:1.
Immerse the disassembled burners in the solution for 15-20 minutes (if the contamination is strong, you can extend the soaking time to 2 hours).
After the allotted time has passed, put on gloves.
Take a kitchen sponge with an abrasive coating and use the rough side to remove dirt from the parts.
Clean the gas passages of the burner using a toothbrush.
Rinse several times with warm water to remove any remaining detergent.
Wipe dry with a napkin or towel or lay out to dry.
Assemble the burner parts.

Important! When cleaning, do not use metal scrapers or brushes, as they may leave scratches and thereby damage the surface of the burner.

Method 2

Remove the dirty burner from the stove.
Take it apart into separate parts.
Take a small saucepan.
Pour 2 tablespoons of 9% vinegar into it.
Add 1 cup of cold water to the bowl.
Bring the solution to a boil.
Lower the burner into it for 25-30 minutes.
Wait, then put on gloves.
Clean the burner using a soft kitchen sponge.
Rinse several times in warm water.
Wipe dry with a cotton towel.
Assemble the burner parts.

Important! Instead of vinegar, you can use regular baking soda, which also effectively removes stains.

Method 3

For express cleaning without soaking, Milam-gel is suitable - a product that is sold in specialty household chemical stores. Use it this way:

Remove the burner from the stove.
Apply a small amount of Milam gel to the surface of the burner.
Leave for about 5 minutes.
Clean with a sponge or brush.
Rinse thoroughly.
Rinse the burners with warm water.
Dry or wipe the burners with a towel until the moisture is completely absorbed.

Main symptoms of a malfunction

If the gas oven stops working, it is necessary to carry out basic gas control diagnostics.
First open the top cover and the burner or hotplate. To do this, unscrew and remove the two side plugs on both sides. Visible signs of malfunction are as follows:

there is gas flow, but with the standard procedure of pressing the button, the flame does not appear;
food is heated unevenly: it can burn at the edges and be cold in the center or vice versa;
the oven does not close or the door does not press well to the base and cannot fully lock;
immediately after ignition, the fire slowly goes out;
it becomes impossible to regulate the heat in the oven;
as long as the handle is held, the gas cannot go out on its own;
the oven smokes, and the fire emits a yellow-red glow;
the flame emanating from the burners has different heights;
the opening of the spirit door occurs with tension, as if it is being held inside;
With little use, the oven becomes very hot.

Important If one or more of these symptoms occurs, it is necessary to inspect the equipment and identify the malfunction. Gas is a dangerous thing, so if you are not confident in your abilities, it is better to call a specialist to your home.

Conclusions and useful video on the topic

The operation of a burner without a divider and the potential size of the flame when cooking directly from the burner is presented in the following video:

An example of the operation of jets for bottled gas in a hob connected to the main gas pipeline is clearly shown in the following video. After replacing the injectors, the flame becomes almost perfect:

Interfering with the design of a gas burner is an unacceptable and risky idea. Residents of apartment buildings must be especially responsible, because in the event of an accident, not only their own lives are at stake, but also the fates of all neighbors. Approach the choice of equipment seriously, calculating in advance the power of the equipment necessary for comfort, so that after purchase there is no need for dangerous and unjustified modification.

Would you like to share your experience of increasing the power of the burner? Tell us about it in the comments block, join the discussion - we and our readers are interested in your opinion.

If you still have questions, do not hesitate to ask our experts and other site visitors - the feedback block is located below the article.

How does a gas stove work?

The design of gas stoves varies depending on the type of equipment. But all such devices include:

burners;
hob;
oven.

Some types of gas stoves are complemented by an electronic control unit for the burner and other components. In particular, equipment is often equipped with a sensor, which, if the fire goes out, shuts off the supply of “blue” fuel.

Burners

The burners consist of the following components:

gas supply nozzle;
swirler;
throttle;
guides;
lid;
divider

The latter divides the general flow of flame into several uniform tongues extending outward. Older stoves use diffusion and kinetic burners. The first ones are installed in ovens. Diffusion burners are distinguished by the fact that gas is mixed with air (due to this process the fuel ignites) in a natural way. Modern stoves use combined burners.

Gas flow control

In the center of the stove burner there is a thermocouple that regulates the gas supply. When heated, this element generates a current that is supplied to an electromagnet. The latter holds the damper open, so that gas flows to the burner continuously. If the fire on the burner goes out, the thermocouple begins to cool. Because of this, the magnet is discharged, as a result of which the damper automatically closes, interrupting the gas supply.

This configuration significantly increases the safety level of the slabs. However, due to the thermocouple, you have to hold the regulator knob down for several seconds.

Internal structure of the stove

Before you start repairing a Gorenje gas stove, it is important to understand the structure of the equipment in order to understand in which area you need to look for a breakdown. And also study the rules for the safe operation of gas appliances

Despite the huge variety of equipment in different price categories, all gas stoves have the same structure, and differences can only be observed in the original parts of each model.

Almost all new models of Gorenje gas stoves are equipped with a piezo ignition system, which often causes frequent equipment breakdowns

A classic gas stove is equipped with four burners, each of which is secured to the inner panel with bolts. The burner includes a lid, a divider and an injector, and a copper tube with a special “American” type fastening is connected to it. This is how gas is supplied to each burner.

If there is an electric ignition system, two candles are supplied to each burner: one is intended for ignition, and is powered by a piezoelectric element, while the second acts as a thermocouple that controls combustion.

The auto-ignition spark plug has a ceramic caftan, which prevents the spark from breaking below the set level, while the candle with a thermocouple is equipped with a bronze caftan, a powerful heat conductor.

The gas stove manifold, which is responsible for controlling the gas flow, is located under the top panel of the equipment. It is presented in the form of a thick tube, from which solenoid valves diverge to each burner - conductors responsible for controlling the gas flow. This way, even if one burner flame goes out, the other burners can still function safely.

What to do if a problem is detected?

It happens that the problem of weak gas supply and flame extinction is caused by accumulated grease on the electric ignition or regulator. By cleaning them from contaminants, you can eliminate this problem. Also check the spark plug; if the holes are clogged, the flame crown will be small or smoky.

It may be worth monitoring whether oxygen is entering the oven. To do this, check that the oven door is closed tightly.

Many, noticing that something is wrong, wonder: what is wrong and how to fix the stove themselves? However, if you encounter any problem that requires appropriate qualifications, it is better not to try to fix the stove yourself. Such intervention without the appropriate skills and knowledge is fraught with big problems.

If you yourself do not have the necessary tools and knowledge to fix problems, then calling a specialist will be the best solution.

If your gas stove has not passed the warranty period, then call the service center of the company where you purchased the equipment. If the warranty period has expired, then call a qualified specialist from other companies in your city. The technician will be able to professionally fix all problems and tell you how to care for the stove.

The cost of carrying out work by specialists

Malfunctions occur suddenly and require quick fixes, especially when a gas stove breaks down. However, not all home appliance owners have the necessary skills. When it is impossible to carry out repairs yourself, you have to call a specialist to your home. What expenses await the owner:

replacement or repair of a gas supply valve - from 300 to 1,200 rubles;
nozzle cleaning - from 400 rubles;
replacing the oven lamp - from 400 rubles;
gas adjustment - from 500 to 900 rubles;
lubrication and cleaning of rods on the feed lever - 900 rubles;
replacement of rods - 1200 rubles;
thermocouple replacement - 900 rubles;
replacement of the ignition unit - 900 rubles;
cleaning of supply contacts - from 900 to 1,100 rubles;
change of sealing gum - from 500 rubles;
replacement or repair of a spark plug - 800 rubles.

Prices depend on the stove model and the region where household appliances are serviced and repaired.

What else could happen

Additionally, I will explain that the absence of a flame or its unstable combustion can be caused by a broken valve. Some models use high voltage relief valves, some use low voltage

It is important to know which valve is in the oven, since outwardly they may look the same. If you install a low-voltage valve instead of a high-voltage one during repairs, you can burn it

There is no need to climb here on your own - this is the work of a master.

If the oven does not want to ignite and all the listed components are working properly, the reason may lie in the gas supply. The problem is easy to recognize - in addition to the lack of combustion, when you turn the knob, you cannot hear a short hiss of gas. If the device operates from a central network, it is better to check the shut-off valve; it is often simply closed. When powered from a cylinder, it makes sense to look at the condition of the gearbox, in case it is also blocked. You also need to check the pressure in the cylinder in case the gas suddenly runs out. If everything is in order, but there is no fuel supply, you should immediately call the gas service. Lack of gas in the system is a dangerous call and can lead to air congestion.

If the oven is operating with a catastrophically low flame pressure, there is an incorrect ratio of the air-gas mixture supplied to the burner. If it is necessary to increase the combustion intensity, adjust the air damper.

What you absolutely can’t do yourself

Unlike situations when a gas oven goes out due to faults that do not require serious repairs that have arisen as a result of improper operation of the device, in some cases you should not try to find and fix the breakdown yourself.

Therefore, it is strictly forbidden to repair the oven on your own in cases where:

if the thermostat is faulty, the flame is intermittent and goes out;
contact damage occurred in the gas control system:
The timer does not work;
The electrical module is faulty.

You should also not repair damaged electrical contacts yourself. It must be remembered that repairing gas equipment or other manufacturers requires serious knowledge. The operating rules for the stoves prohibit their independent installation and repair.

In the absence of the right to warranty repairs, special workshops are available to consumers. The technician will competently diagnose, fix the problem and give the necessary advice on the safe operation of the stove with a gas oven.

How does electric ignition work?

Electric ignition makes it possible to light the stove safely. It reduces the possibility of getting burned to a minimum, because with piezo ignition there is no need to use lighters or matches. There is also no contact with flame. With electric ignition, gas ignition occurs from the activation of a piezoelectric element on the gas device. The piezoelectric element gives a spark, after which automatic electric ignition takes place without the use of other devices. Repair of gas stoves with electric ignition can be done either with the help of a specialist or with your own hands: it all depends on the type of breakdown and knowledge about the operation of the structure.

Step-by-step troubleshooting instructions

Algorithm for identifying the most common equipment failures:

Check the presence of voltage at the terminals of the supply cable using a voltmeter. After making sure that power is supplied to the control panel, press the “Sand” button. Sound and light indications are activated on the touch panel.
At the input circuit breaker located in the power supply distribution board, the voltage at the upper contacts is checked. This process is carried out using a multimeter, a low voltage indicator (LV) and a single-pole indicator.
The supply of voltage to the mechanical and electronic control mechanism is carried out using a special unit. To check the serviceability of the cooking zones, it is necessary to measure the electric current one by one with an ammeter.
Tubular electric heaters, temperature measurement sensors, electrical switches, make and break contacts, and all kinds of regulators are checked for malfunctions and to detect the causes of device failure.

Causes of failure

Why doesn't the gas stove work? There are two most common reasons for poorly functioning electric ignition:

electrodes do not produce a spark;
the electrodes spark without stopping.

One of the reasons why the electric ignition of a gas stove does not work well is grease on the buttons. Solving the problem is very simple: just clean and dry the components of the hob, all the buttons in order to repair the electric ignition of the gas stove caused by contamination.

Another possible cause of failure is a crack or broken ceramic insulation on the spark plug. A dirty spark plug can fail if dirt accumulates on it. Also, the spark plug may stop working properly due to poor sealing or oxidation of the rod made of steel. In addition, the element may crack due to careless handling. In this case, the spark begins to strike to the side. The only way out of the situation is to replace the spark plug.

When the spark generation unit (ignition transformer) burns out, the button you press does not create a spark. If the piezo ignition on a gas stove does not work, it is easier to buy it than to repair it. It is possible to repair this element, but it is too expensive - it is cheaper to purchase a new one.

When washing the stove, water very often gets into the contact area of the power buttons. High humidity creates all the conditions for these contacts to oxidize, become hard and break over time. In some cases, the opposite happens - the contacts may stick together and not work correctly. It’s easy to solve a similar problem with automatic ignition not working - just cleaning and drying is enough, after which the functionality of the hob will be restored.

For what reasons does a gas oven turn off?

All kitchen equipment of this type is divided into dependent (together with the stove) and autonomous, electric and gas.

Advantages of gas-powered equipment:

simplicity and low cost of operation;
independence from power outages;
Possibility to connect to both a gas pipeline and a cylinder.

There are three disadvantages: a limited set of functions, a small range and high cost.

Stove with gas oven

If the electric oven of a gas stove goes out during operation or immediately after the handle is released, then:

smokes gas;
the gas supply valve is jammed;
the door fits too tightly;
the magnetic valve or thermocouple is worn out;
The thermostat has been calibrated;
the connection in the gas control system has become loose;
The thermostat has failed.

It is impossible to carry out diagnostics and repairs on your own due to the lack of diagnostic equipment, components and spare parts. You need to call the service center and ask the operator about the cost of the service and the technician’s working hours.

Autonomous gas oven

An autonomous gas appliance most often turns off if the electric ignition does not produce a spark or, conversely, constantly sparks. There are many reasons for the problem; they can be determined after disconnecting the ignition from the network and removing the electronic unit.

Most often, the ignition system fails if:

burnt tracks (soldered joints);
the resistor burned out (turned black);
one or both windings of the transformer have burned out;
the capacitor has failed (swollen) or the tourist;
candles broke;
contacts have oxidized (due to moisture ingress);
the handle is dirty (overgrown with grease);
the injectors are clogged.

The handle can be cleaned independently; other causes can only be eliminated by a specialist.

This is especially important if the device is under warranty. A service center specialist will diagnose and replace spare parts free of charge.

The oven does not work - the main reasons

Before calling a technician to repair the oven, you should check whether there is a gas supply in the pipe. To do this, try lighting the burner on the hob. If gas enters the burner, it means that the oven is really faulty.

The second point that you should pay attention to is the presence of electric current in the network. Without it, the electric ignition will not work.

If everything is normal, then the oven is really faulty. You should not try to repair it yourself. Without the necessary spare parts and experience, doing this will be very problematic and even dangerous.

The main malfunctions of gas stove ovens Gefest, Hansa, Mora and others include:

When you press the ignition button for a long time, you can hear the hiss of gas, but the flame does not ignite.
The flame ignites, but after releasing the button, it immediately goes out.
The flame burns for 5-10 minutes and goes out on its own for no apparent reason.
The flame is very weak. Food cannot be cooked.
The flame is very strong and impossible to regulate. The food is burning.
It is impossible to turn the gas supply valve.

Self-modification of the nozzle

If you determine that the equipment has unsuitable nozzles and there are no replacements, then you can find many recommendations for modifications on the Internet. They explain in detail how this can be done using a soldering iron, solder, sandpaper and sewing needles. It is recommended to check the performance of the resulting product experimentally.

But please note, this is very dangerous! The result of such an experiment may be a leak.

You should not expose your life and health to such danger. It's better to buy a new part.

Design and main components of an electric stove

The electric stove looks very impressive - it is a complex household appliance, but its design is quite simple, and all the main working elements are located in a special heat-resistant case, which is made of stainless steel.

The operating principle is similar to all electrical household appliances: current passing through heating elements (heating elements) heats them to a given temperature. The stove has several burners on the hob, and their number varies: a minimum of two, and the standard is 4 pieces. For example, the budget electric stove Mechta 15M has only two burners and a small oven, while the product of Belarusian engineers Hephaestus has a standard set of burners and a large oven.

The structure of the burners is quite diverse. The classics are burners on an enamel hob with heating elements inside, modern ones are solid ceramic surfaces with various types of heaters built into them. Let's look at the main types of burners.

Old domestic versions are equipped with cast iron products; they heat up slowly and also cool down, creating a steam effect in the kitchen, but they are resistant to moisture and high temperatures.
Tubular spirals - they are made of a hollow tube; when heated, such devices not only give off heat, but also promote the circulation of warm air inside their body, which significantly increases their efficiency. These products are very difficult to repair yourself.
Ceramic burners are very simple in design, they are easy to repair at home - a nichrome spiral is placed in special cells in a circle and secured. Modern models increasingly use glass-ceramic solid plates - they are more durable and easy to clean.
Halogen devices are special burners with a similar emitter that are installed in different places on the hob. A stove with such burners provides fast heating, in a second, and low energy consumption, so they are the most economical, but only professional craftsmen can carry out repairs.

All models of modern stoves use a special cross-section power wire to transmit current to the burners; in addition, they are connected to regulators and thermostats, ensuring their protection from overheating.

Incorrect setting

If the gas stove is powered by a central system, there is a high probability of a problem arising due to incorrect settings of the device. Then you should seek help from specialists. Sometimes consumers try to solve the problem on their own, which is possible if you study the following features of the internal structure of the burner:

The burner includes a divider - this is a special part, externally similar to a flange bushing. To ensure uniform gas distribution, the divider has tower teeth located along the entire perimeter.

A cover is placed on the divider - a special round stainless steel plate.
Some models are equipped with an electric ignition system, so under the burner you can find a candle located on the side of the divider. In such models, the gas stove must be ignited by a spark.

Device under the burner with electric ignition

In modern models, under the burner you can find a sensor that determines whether the burners are burning. If the gas does not burn, it means that its supply has stopped.
When you remove the lid and divider from the burner, you can see the jet - this is a special part that looks like a small bolt with a hole punched along the axial direction.

Modern model of a gas stove and a disassembled burner

Expert advice

Gas oven repair specialists advise paying attention to the following points:

Some models of gas stoves have plastic tap handles that are attached to the stem by means of a metal plate that is inserted into a groove. With use, the handles begin to become loose, the record flies out and is simply lost. The problem can be resolved. You need to take a metal canning lid and cut a suitable plate on it. By inserting the part into the groove on the handle, you can avoid such a delicate problem.
The extinction of a fire is not only due to a lack of gas or a small amount of incoming oxygen. The problem may be that the iron part that is located next to the burner heats up and causes a current to form. It holds the magnetic valve in the operating position and may prevent gas from flowing to the burner. The problem is solved with sandpaper: it cleans the parts.
Advice If the procedure does not help, the gas stove also does not work, you need to change the thermocouple.
If a misalignment occurs in the gas burner, it is worth checking its correct installation. If the problem occurs after washing, then the installation was not performed correctly. You need to remove the part and reinstall it. If a repeated attempt fails, then it is better to call a specialist. In rare cases, the problem lies in defective products and requires a major replacement. Although this case must be confirmed by the master.
To make the fire in the oven stronger, since it begins to burn weakly or goes out at the wrong moment, switch to blue fuel with a lower pressure: in this case, it is necessary to replace the burner nozzle (with a wider nozzle) and adjust the oven thermostat.

It's not just gas stoves that break. Our website contains useful materials about breakdowns and repairs of electric stoves and their ovens, induction stoves, hobs, ceramic and glass-ceramic.

Handles don't turn

A fairly common problem is the inability to turn on the equipment due to the fact that the fuel supply knobs do not turn. There may be 3 main reasons:

Adhered grease and dirt make it difficult to turn;
the grease on the faucet has dried out;
element failure.

You can fix the problem with contamination and lack of lubrication yourself, but if you do not know the design of your device and what lubricant is best to use, then it is better to call a specialist.

If the handle turns with great difficulty, then you should not try to turn it by force; perhaps a small object has gotten between the body and the plug, which interferes with the movement of the rod. The defect can be eliminated by disassembling the device, and in order to avoid such an annoying phenomenon in the future, it is necessary to carry out preventive measures.

Sometimes the opposite problem occurs when it is not possible to light a fire due to turning the handle 360°. This usually happens on devices during long-term operation. The reasons are loose seats in the handle, unscrewed screws of the tap holder, disconnection of the stem and stud. Such problems can be eliminated by replacing parts and returning them to their original positions.

Solenoid valve - the second gas control element

Most gas stoves and hobs are equipped with safety sensors - a gas control solenoid valve. They shut off the gas supply if danger arises when operating the gas stove. If a gas burner or oven goes out for any reason or is blown out by a random flow of air, the solenoid valve will shut off the gas supply after 5 seconds. The solenoid valve starts working after 4 seconds with constant heating of the thermocouple, if this does not happen or the time to turn on the burner has increased to 10 seconds, we can say that the gas control system of the stove is not working properly and most likely you need to repair the hob.

Poor quality gas cylinder

If the gas stove smokes, then the reasons lie in two possible problems.

The first is based on an excess of sulfur content - it is this that produces that black smoke when burned. In most cases, cylinders are filled with propane, but high sulfur content in them is also possible.
The second reason is unregulated gas pressure, which exceeds the nominal values of the device. In most cases, the problems presented are encountered when using gas cylinders.

The cylinder is used to supply gas mainly in dachas

In the first case, the problem lies in low-quality gas - cylinders are often filled with gas that does not meet the standards. The presented actions of unscrupulous sellers do not bring danger, but cause a lot of inconvenience in use. If the cause is high sulfur content, consumers are advised to contact Rospotrebnadzor to hold sellers accountable.

If consumers see a gas device smoking, they need to take the following actions:

First, decide on further actions - use the gas in its current state, or try to reposition the cylinder or stove. In this case, you should be guided by the characteristics of the soot content - so that less damage is caused to the entire device.
Next, they turn to the organization that refills gas cylinders. When you apply, you can receive compensation, but you will have to prove that you are right – the increased sulfur content in the gas.
If you cannot receive compensation, you should contact Rospotrebnadzor to restore justice.
Already after the application, an analysis of the gas contained in the cylinder will be carried out. If a decision was initially made to restore justice, it is recommended not to take additional independent actions in relation to the gas cylinder. During the examination, specialists will not only confirm the increased sulfur content, but also determine the amount of remaining gas. This will help calculate the amount of compensation.

Carbon deposits on the pipes

Everyone is used to thinking that natural gas burns cleanly. This is true, but not 100%. Any fuel contains a minimum amount of impurities that form ash during combustion. Over time, it accumulates and clogs the holes.

What to do if the gas panel burner does not light

The presence of carbon deposits creates pressure and interferes with the proper functioning of the device. The flame may not burn or go out too quickly. The burner must be removed and cleaned. Depending on the oven model, disassembling the housing is required. Most often, to access burners with a jet, you need to remove the door and bottom panel of the device.

I note that in some models, to dismantle the door it is not enough to unscrew the hinge screws. The loops may need to be unbent and folded back

By the way, it is advisable to immediately pay attention to the condition of the seals. If necessary, they are replaced with new ones

When opening the case, be aware that some metal parts have very sharp edges.

Be careful not to cut yourself

As a rule, the pipe is placed on the gas supply pipe and secured with 1-2 bolts. The burner itself can be of different shapes, but essentially remains a piece of metal with holes, there is nothing to break here. However, there are holes near the burners for air supply. If they are clogged, they should also be cleaned. Despite the simplicity of the work, it is better to entrust it to a master. If you act without experience, you can snag the gas control, causing it to break.

If cleaning does not help, it may be a problem with the seal of the structure. In this case, there may be a smell of gas, which requires immediate repair.

The electric ignition has failed

Electric ignition may not work on 1 burner or on several at once. If you cannot turn on all the cooking zones at once, then most likely the fault lies in the high voltage source. You cannot disassemble or repair something yourself; it is life-threatening.

It is also recommended to check the quality of the power cable and plug; the piezo element may not work if the wire is pinched, bent or the insulation on it is damaged. Melting of a plug or socket also negatively affects the operation of the device.

If performance is maintained on at least one burner or in the oven, then the defect could affect the insulator, which cracks during intensive use. Contacts and ignition wires are also susceptible to damage; to check, they must be tested. As a rule, the contacts themselves are rarely damaged, because the current in the high-voltage circuit is insignificant, but the insulation of the wires fails during the heating process, shorting to the housing.

Electric ignition does not work on two burners

In some cases, a gas stove on two burners does not light. Sometimes lighting it with a match helps - everything works normally, without interruption. The cause of this malfunction is damage to the spark plug responsible for ignition. We repair electric ignition as follows: clean the spark plug and look at its condition; perhaps it’s enough just to clean the spark plug’s power wire.

If there is a crack on the element, we buy a new part and put it in place of the old one. The electric ignition may also break down due to a faulty ignition button. Moisture or small debris could have gotten into it, or it could have been damaged mechanically. To fix this, you need to clean the oxidized buttons or replace them if they are mechanically damaged.

Specialized repair service "Remontano"

If your gas stove or hob does not turn on, do not panic and run to the store to buy a new appliance. Often, breakdowns of such units are minor and can be easily repaired by the hands of professional craftsmen.

The specialist performs diagnostics, maintenance and restoration work, regardless of the brand of the device. The company has its own warehouse of spare parts for equipment: Gefest, Hansa, Ardo, Mora, Ariston and others. If you need quick and reliable repair of household appliances at home, call us at 8(495)777-19-19 or leave a request on the website. We are open every day, seven days a week, from 7:00 to 23:00.

How to fix it?

Most often, when gas ovens malfunction, owners are in no hurry to contact specialists, hoping to carry out repairs themselves. What kind of breakdowns can be repaired without danger with your own hands? This is discussed below in our article.

Cleaning the regulator knob. Before starting repairs, turn off the gas supply. Troubleshooting begins with cleaning the taps. After removing carbon deposits, dirt and grease from them, clean the spring. Wipe the cork carefully so as not to damage it. Disturbing the surface will cause gas leakage. Use only a soft sponge. Next, the plug is treated with graphite lubricant without touching the holes. Remove greasy deposits from the stem with a knife. Afterwards, the handle is assembled in the reverse order of disassembly.
How to fix oven doors. Over time, the oven door becomes loose, causing it to not fit tightly or not to close. To fix the problem, unscrew the mounting screws connecting to the stove. Having loosened them well, move the door in different directions until you find a position in which it is firmly seated on the hinges. To control, place a sheet of paper between the seal and the edge of the oven. If it does not clamp well, do the procedure again. After installation on the hinges, the bolts are tightened into place.

If it is noticed that the loss of heat is associated with damage to the seal located around the perimeter of the door, replacing it will not be difficult.

Remove the old seal. In some oven models it may be attached with screws; to get to them, pull off the protruding edge of the rubber, in others it is glued.
Wash the channel and door with liquid detergent. Clean off any old caulk or adhesive residue. Degrease.
Install a new seal by starting from the top, then down and to the sides. Complete the process by bringing the edges together at the bottom center. If the elastic needs to be glued, choose a food-grade adhesive that is heat-resistant up to 300º.

Among other failure options.

Checking and cleaning the thermocouple. The oven burns as long as you hold the handle - then you need to check the thermocouple mount. In the lowest position it should touch the tongue. If the placement is incorrect, most models allow you to adjust with screws. It is possible that the thermocouple contacts are dirty and this is preventing the flame from being maintained. Try cleaning the part with sandpaper.

Problems with burner control knobs

Gas supply handles for the burner are one of the most necessary parts; without them it is impossible to use the stove. Behind the outer skirted flag, which you turn, there is a gas tap, which can have a gas control sensor built into it.

Electric ignition built into the handle is rare on Hephaestus stoves - it is usually located with a separate button.

Over time, the knobs may stop turning, become stuck, or become loose. We'll tell you what to do about it later.

The handle is difficult to press and turn

This problem is not uncommon; if you start it, the handle may stop turning completely. The cause is usually grease that has accumulated between the flag, skirt and front panel of the cooker.

Hot, it splashes during cooking and easily flows into all the cracks, and then cools, thickens and turns into a kind of glue.

Carefully pry up the skirt and handle with a knife, screwdriver or other flat object. Do not use too much force - you may damage the enamel or plastic.

To get rid of the problem, the flag with the skirt must be removed from the stem and washed thoroughly. The handle needs to be pulled towards you - it is simply pressed tightly onto the rod, without latches or other fasteners. For convenience, you can grab it with pliers, preferably through a non-slip cloth, one of those sold for cleaning.

The skirt usually comes off on its own after the handle is removed, but if it does not turn with the flag, it can be secured with a latch. In any case, you can pick it out with a knife. Remember its position so that when assembling, the latches close to the panel or flag.

Many models have a reinforcing metal plate in the handle; do not lose it. After washing all the parts, as well as the front panel under the handle, put everything back in place. Don't forget to install the spring if you had one.

The checkbox scrolls or jumps off

This problem is rare with Hephaestus slabs, but it does happen. The reason is usually that a metal plate has fallen out of the flag and is lost, which clings to the recess on the rod.

You can cut such a plate from a metal preservation lid and insert it into a special groove, or buy a new flag. If the handle on your model is completely plastic and its inside is licked off, only buying a new one will help.

The handle turns hard

It happens that even after the flag and skirt are perfectly washed, the handle still turns tightly. The reason is that the lubricant on the gas taps has run out.

It is better to invite a specialist to carry out preventive maintenance, because mistakes during such repairs can lead to leakage or clogging of gas supply pipes

If you decide to lubricate the gas taps yourself, buy a special graphite lubricant for this. Turn off the gas supply to the stove. Then remove the handles and the front panel - we described how to do this above.

In Hephaestus slabs, the stem is fixed in the tap with a flange connection; to remove it, simply unscrew 2 bolts on the sides. Immediately wash the stem from grease and dust.

Then the spring and the tap plug are removed - the last one needs lubrication. This is a cylindrical part with a through hole and a cut on the side, through which gas is supplied to the burner. You need to lubricate the cork very little; the layer should be invisible, but noticeable to the touch. It is more convenient to put a little lubricant on your finger and rub the plug.

After assembling the faucet, do not rush to replace the front panel. First, put the flag on the stem without it, open the gas and apply a soap solution to the tap. If no bubbles appear anywhere, wipe everything dry and reassemble the stove.

Broken “gas control” of the burner

If after cleaning the burner continues to go out, the fire burns, but does not register, the cause of the malfunction lies in the automation. It is possible to determine the state of the automation using a multimeter. A thermocouple measures the voltage when heated. The solenoid valve checks for winding breakage.

6 reasons why a gas stove burner does not work.

We repair automation. “Gas control” is a set of parts working in pairs (thermocouple and solenoid valve). When heated, the thermocouple produces electricity to magnetize the valve. Loss of contact, as well as mechanical wear, will lead to rupture and gas combustion will stop. The repair is simple: remove the table tray and securely fasten it in a vertical position. A thin copper-colored wire from the burner to the gas stove faucet is called a thermocouple. The connection point between the tap and the thermocouple is a contact. Separate the parts and clean the contacts with sandpaper, connect and tighten securely.

Tip: If the gas control stops working, replace the thermocouple or solenoid valve. Install original spare parts according to the stove model. Universal parts differ in the diameter of the seats. The fit and installation height of the thermocouple plays an important role.

Why does the oven go out after releasing the handle?

Reason #1. The thermocouple is faulty.

Today, most gas ovens and ovens use an automatic control system that makes them safe to use. One element is a thermocouple, which is attached to the frying burner bracket at a distance of 147 mm from the vertical axis of the burner.

The gas oven is turned on by pressing and turning the tap handle. Electronic ignition ignites the burner where the thermocouple is located. The thermocouple is directly connected to the solenoid valve with a threaded connection. When heated, the thermocouple produces a weak voltage to magnetize the valve. The magnetic field keeps the valve open and gas flows to the burner.

If the tip of the thermocouple burns, the valve will instantly shut off the gas supply, so if the gas oven does not work after releasing the handle, the fault is due to a faulty thermocouple of the gas control system.

Reason #2. Thermal solenoid valve is faulty.

The second element of the security system. Its purpose is to stop the gas supply to the burner if the operating rules are violated. The valve consists of: electromagnet, winding, bottom valve.

When you press the handle, the lower valve rests against the upper valve plate, as a result of which the gas is directed to the burner in the oven, where the thermocouple is ignited and heated. The resulting EMF from heating the thermocouple returns to the valve, where the electromagnet is able to be held open. If the valve receives mechanical damage (winding insulation failure), the valve will move away from the seat and shut off the gas supply.

OR, TRY TO CLEAN THE CONTACT

To a greater extent, the gas in the oven goes out due to poor contact between the thermocouple and the valve.

For this:

We open the cooking table of the stove;
Disconnect the thermocouple from the valve.
We clean the contact with sandpaper and degrease it.
We tighten the nut back.

Common causes that you can solve on your own

When choosing kitchen equipment, most women choose the best option, a gas oven. It is characterized by ease of operation and maintenance, a wide range of capabilities and the most precise settings. Despite the many advantages of use, there is a common problem during operation: the oven goes out a short time after setting it on fire. What could be causing this problem?

There are several main reasons:

Lack of oxygen in the gas furnace;
Shut off the gas supply valve;
Fire sensor problems;
Loss of pressure in the pipeline;
Incorrect operation of the burner due to contamination;
Incorrect burner setting after removing and cleaning it.

These problems can be easily fixed on your own, without calling a technician: no special skills or a lot of time are required.

Solving the problem yourself:

The lack of incoming oxygen is eliminated by igniting the oven with the door open.
The tap responsible for the gas supply is accidentally closed during cleaning, and then forgotten to open. To eliminate this problem, you need to open the valve.
Additional flame sensors are provided to ensure fire safety. They monitor the oven temperature. If there is no heating, the sensor turns off the gas supply. To solve such problems, hold the power knob longer than usual and turn on the maximum temperature when warming up. The problem is typical for ovens equipped with gas compressed in special cylinders. The sensor does not heat up due to the slow increase in temperature and turns off. To eliminate the problem, the cylinder is refilled or a new one is purchased.
Fat and pieces of food getting into the burner can cause it to fail. The blockage is visible to the naked eye: the burner lights intermittently, and in some areas there is no fire. To solve the problem, the contaminated part is removed and thoroughly cleaned, after which it is returned to its place and the oven continues to be used.
After cleaning, the burner is often installed incorrectly. To troubleshoot problems, you must remove and install the burner correctly.

A crack has appeared on the ceramic automatic ignition spark plug

The automatic ignition system is the most unreliable and capricious thing in the entire stove. Breakdowns here are not uncommon, especially given the poor quality of some gas stoves. Normally, the system should work without failures. By the way, I have seen excellent “seven-core” ignition in Gorenje and Smeg gas stoves.

During diagnosis, the first thing to examine is the electrodes. An electrode is a ceramic candle, a rod if you like, that has a metal core. You should carefully inspect it to make sure there are no mechanical damage or cracks. The candle itself must be securely fixed next to or inside the burner.

A sign of a crack is sparking on some burners. They will require replacement spark plugs. To access damaged parts, the cooking table is disassembled. The spent candle is disconnected from the burners (by the way, there are locking rings here, they cannot be lost) and from the impulse block. A new one is installed to replace the worn-out node and the connection is made.

Tip from the expert: never press the ignition button if the burners are removed from the stove. This way you will get a breakdown.

What to do if the flame changes color

If the flame changes color, the burner is not working properly. The reason may be that there is not enough oxygen in the gas-air mixture for the gas to completely burn. It should be understood that this situation, when the flame changes color from blue to white, orange or red, is seriously dangerous, as it causes a large accumulation of carbon monoxide. Carbon monoxide is deadly to humans!

Thus, with a carbon monoxide concentration of 0.1%, a person can suffer acute poisoning or even death. Therefore, if you discover that the burners are not working properly, namely, the color of the flame has changed, it is necessary to urgently clean the burners from dirt. This will ensure safe further use of the gas stove. To do this, you need to thoroughly wash the burner sink, its cover, and then clean the burner nozzle of dirt. You can learn more about the cleaning process by reading the first chapter of this article.

Having new gas equipment does not guarantee that there will be no problems with the burners. If the flame on a new stove burns in any color other than blue, this means that there is a protective lubricant in the structural parts that may prevent the required amount of oxygen supplied.

If after the cleaning procedure the result has not changed and the stove continues to work poorly, it is necessary to check the settings of the gate valve - a device that regulates the amount of oxygen supplied to the gas. It is not advisable to adjust the gate yourself; it is better to invite a specialist who will correctly adjust the device and check the result of its operation.

When deciding to adjust the adjustment yourself, you need to understand that if the damper is moved towards the nozzle, the primary oxygen supply channel will be blocked. This will make the problem worse rather than solve it. Therefore, in order to correctly adjust the gate, the damper must be moved in the opposite direction, that is, from the nozzle. The specific distance to move the damper is determined through trials and checks.

Whether the burner is working normally or not can be determined by the following characteristics:

Flame color: blue
The size of normal flames is from 2 to 2.5 cm.
The flame burns silently
There are no flames coming off

Sometimes the cause of improper combustion is poor quality gas supplied in the pipeline. To identify this reason, you can ask your neighbors if they have the same problem. If confirmed, you must contact the gas service. The time frame for solving the problem in this case will not be determined. But if the color of the flame changes the gas cylinder, then you can try replacing it with another one and the problem will be solved.

What to do if the burners go out

There are several other types of problems with gas stoves that cause the burners to go out. Among them the following stand out:

Incorrect burner operation leading to fire extinguishing
If the burner is not working properly, it is very difficult to turn on the tap.
All burners burn poorly at once

Regardless of when the burner goes out: immediately after setting fire or a little later, the reasons for the extinguishing are the same. The main ones are:

Problems with the gas control system. This causes the burners to malfunction. In this situation, it is necessary to replace the electronic valve or temperature sensor, and possibly the entire system.
The nozzle is dirty. In this case, it is necessary to clean the nozzle (cleaning instructions are described above in this article) or replace it.
The temperature sensor does not heat up when the burner is lit. The reason is improper handling of the device, in which it takes an incorrect position.

Nozzle does not fit

The nozzle, or nozzle, is the main element of the burner, responsible for the gas flow. The burners in all modern gas hobs have different power levels and therefore differ in diameter. The nozzle is responsible for supplying the appropriate amount of gas: the part with a small hole is intended for a small burner, and the part with a large hole is intended for the largest one.

The injectors differ in their purpose. They are:

for operation from bottled gas;
for operation from main gas.

Externally, the products are the same, however, the nozzle intended for bottled gas has a smaller hole than the nozzle for main gas

This is important to consider, since when installing a gas panel in a country house and connecting it to a cylinder, the nozzle should be replaced. If the procedure is not followed, the burner will smoke.

As a rule, modern devices are equipped with two nozzles, so that if the gas source changes, the stove can be adjusted.

If smoking due to an unsuitable nozzle, change it. If you have lost a replacement kit, purchasing the necessary products is the most suitable option. Look in the documentation to see what diameter of the jet is required. Sometimes you cannot find the necessary spare parts, then select injectors with a smaller diameter and try.

The composition of the gas has changed

It is rare, but it happens that the composition of the main gas changes and smoking occurs. This problem, as you understand, cannot be corrected on your own. To make sure that it is the gas distribution stations that are to blame for the soot, a survey of neighbors will help: if everyone has such problems, then wait for corrections or contact the relevant authorities.