It is impossible to imagine a kitchen without hot water. Where can I get it? There are few options:
- open the hot water tap;
- heat in a saucepan or kettle;
- install a water heater.
Even in large cities, not all houses and apartments are connected to hot water; in the summer it is often turned off, and the quality of the water is sometimes unsatisfactory.
In private houses, cottages and dachas there is no centralized supply of hot water at all. Heating on a stove or in a kettle, as they say, is more expensive.
The most comfortable and convenient way is to use a modern water heater for the kitchen. How to choose the most suitable one from a large number of models?
Advantages of electric water heaters for the kitchen
Hot water in the kitchen is necessary for many reasons, be it cleaning, sanitizing cutlery and dishes, or preparing food. This section presents models that are suitable for any room, with various installation options. Thin formats can be placed even inside a cabinet and get maximum free space and hide utility lines. Some models can be mounted vertically or horizontally, or purchase more versatile units that can be installed in both positions. In our online store you can buy a wide range of compact water heaters for the kitchen with delivery throughout Russia, Belarus and Kazakhstan. All products are certified and have a factory warranty.
How to stylistically design a room with a boiler
To make the room attractive after installing the boiler device, it is necessary to use the following stylistic design options:
- Provence is attractive because it combines white facades with a water heater painted in a similar tone. It is possible to use designs with flowers.
- The loft style uses the device effectively.
- It is characterized by the presence of a delicate country-style color palette. The structure can be covered with panels painted blue, white or peach.
The product is also installed in rooms decorated in rustic, industrial, Russian and a number of other styles.
How to choose
Before purchasing a storage boiler for the kitchen, you should understand the important technical parameters of the equipment:
- The power of the device affects the heating rate. More powerful models are equipped with several heating elements, and to save energy resources they provide the ability to adjust power.
- The input voltage in different models can be 220 or 380 W, pay attention to this parameter before purchasing.
- The tank capacity is selected depending on the number of consumption points. For the kitchen, 15-20 liters is usually enough.
- The device control can be mechanical or electronic. The presence of a display allows you to receive information about the current state of the system, errors and malfunctions.
- Before purchasing, you should inquire about the overall dimensions of the water heater if the equipment is planned to be placed in a closet or under the sink.
Regardless of which type of water heater you choose, consider the following:
- Always have a certified professional install it, do not attempt to do it yourself as this will void your manufacturer's warranty
- Choose a reliable brand with a long history.
- Choose an appliance that saves energy and water, this will save you on utilities in the long run.
Flow-through
Their advantages are that they do not take up much space. Thanks to its compact size, it can be installed in a cabinet under the sink.
The disadvantages of such a heater are that it is impossible to simultaneously obtain a large flow of water. Another disadvantage is the comparatively higher electricity consumption due to higher power.
Keep in mind that the more powerful the heater, the greater the load on the electrical network. For apartments in old buildings, it is recommended to choose equipment with a power of no more than 5 kW.
The price starts for such heaters from 1,000 rubles.
Advantages
The models of water heaters for the kitchen presented in our online store are distinguished by a modern and convenient design. The compact dimensions of the equipment allow it to be installed in any convenient place, and the device operates from a regular household outlet. The internal tank is made with an anti-corrosion coating, which ensures a long service life. The external heat-insulating box allows you to maintain the set water temperature longer, which means it reduces energy consumption. Models are equipped with various protection functions, for example, against overheating, power surges, excess water pressure, and leaks. We sell only certified equipment with a factory manufacturer's warranty. Additionally, we provide installation and maintenance services for equipment.
Our online store offers compact water heaters at low prices. We are representatives of famous domestic and world brands: Aparici, Ariston, Atlantic, Baxi, Bosch, Clage, Eldom, Electrolux, Garanterm, Gorenje, Haier, Hyundai, Kospel, Metalac, Nofer, Polaris, Royal Clima, Stiebel Eltron, Superlux, Tesy , Thermex, Timberk, Unipump, Zanussi, Resanta, ElBET, Alvin. It is possible to purchase goods for cash and non-cash payments, as well as on credit. Additionally, we provide design, installation and maintenance of equipment.
Gravity or pressure
This water heater looks like a small container. It is located above the level of the tap. The valve that restricts the flow of water into the container resembles the one you see in a toilet cistern. The position of the float will depend on the amount of water. As the water level decreases, the float drops and the valve opens. The water level rises, the float rises, and the water supply ends. Such a system will prevent overflow.
It is worth noting that small holes are often clogged with sand particles and rust can form on them. Therefore, from time to time it is worth replacing this part of the heater.
Atmor Classic instantaneous non-pressure water heater
The advantage of such a non-pressure water heater is the ability to fill water independently. If necessary, you can change the tubular electric heater. It is distinguished by reasonable cost and compactness.
As a minus, one can note the relative low efficiency and at the same time considerable energy costs; it does not have an insulating layer.
An instantaneous pressure water heater is a practical solution. It works almost the same. Only the water supply here is carried out under pressure. A thermostat is installed in the water heater to adjust the temperature.
The power of the tubular electric heater can be changed and thereby monitor the water supply. Accordingly, if the pressure is lower, the water heats up faster.
You can read about the types of heating elements for water heaters here.
Pressure instantaneous water heaters for the kitchen have their advantages:
- good pressure;
- compact dimensions;
- independent control of temperature and energy consumption.
The disadvantages include considerable costs for electricity, the high price of the structure and the difficulty of installation.
Storage water heater Gorenje GT 15 U/V6 under the sink, 15 liters
Reviews from customers
Maria, Moscow : “We installed a flow-through, non-pressure kitchen water heater. Convenient to use. But after 8 months the water pressure became less. It turned out that the diffuser needed to be replaced due to the fact that it was clogged with debris from the water supply. The procedure is not very complicated, but I did not expect to carry out maintenance so often.”
Sergey, Moscow : “I have a 100 liter storage boiler installed. We set the temperature ourselves as desired. The warmer the weather outside, the lower the water heating temperature. It is very convenient and economical. A family of three, so the volume is quite enough. Moreover, the wiring is at three points: bathroom, washbasin and kitchen. We are satisfied".
Basic rules of operation and care
If you follow the basic rules of care, any device will serve you for a long time.
- The main problems with boilers are scale and corrosion. To at least slightly reduce the aggressive effects of hard water, install softening filters. Also, as an anti-corrosion protection, a magnesium anode rod is used - it is this that will take on all the rust and will be destroyed instead of your heater tank. It is necessary to carefully monitor his condition. As a rule, the magnesium anode needs to be replaced every one to two years, otherwise it will completely collapse and corrosion will reach the boiler. Prevention should be done by a master - he will replace the anode with a new one and remove the accumulated scale from the heating element. The blast valve is also cleared of scale and debris.
- Very often, heaters get damaged because users turn them on before water runs into the device. After the device has been installed and the heater has been connected to the water supply, be sure to fill the tank with water, and only then plug it in.
- The heater may fail if it is turned on and off frequently (to save money). It's better to just reduce the temperature as much as possible.
- Often, heaters must be positioned so that they are not exposed to jets or even splashes of water. For some models, even condensation or strong steam is harmful. Be sure to study these points in the instructions for the device.
How to get rid of an unpleasant smell from a boiler, watch our video:
As you can see, there is no clear answer to the question of which device for heating water is optimal. Before you start choosing and purchasing a device, you will have to take into account and evaluate many different factors: your needs, the capabilities of your home and space, financial capabilities, the required technical and other characteristics of the heater, etc. Only then will you be able to accept the most appropriate you decide and choose the most ideal option for your home. We also recommend that you familiarize yourself with the large selection of meat grinders in this material.
Main types of water heater breakdowns
Main breakdowns of electrical structures:
- heating element failure;
- storage tank leaking;
- clogging of all kinds of ducts;
- thermostat failure.
In any case, you should not try to fix the problem yourself. To do this, it is better to contact a service center. If the product does not come with the warranty provided by the manufacturer or store, then contact them immediately. After all, after independently tampering with the device, the warranty is automatically canceled and all repair costs are borne by the buyer.
Installation and connection methods
Installation of the structure under the sink
Installing a pressure heater on a faucet consists of the following steps:
- We connect the heating mechanism with the mixer.
- We install the resulting structure on the sink using rubber seals.
- Using sealant, we connect the installed tap to the water supply system.
- Without connecting the installation to the network, turn on the water to check the tightness of the connections. Under no circumstances should there be any water leakage.
Typically, the included electrical wire is 1 meter long. Therefore, you need to take care in advance about the availability of an outlet for connection.
How to install a storage boiler under the sink
Installation under the sink is the most convenient way. This is due to space saving and aesthetic appearance. But for this location of the heater, you need to make sure that in the selected model the water supply connection is made from above. If this is the case, then you can install, be sure to take into account the following:
- A check valve is mounted on the water supply fitting. It is needed in order to prevent the tank from rupturing in the event of a heating element failure, and also eliminates the possibility of reverse movement of water and allows water to be drained if necessary.
- Shut-off valves are installed at the water inlet and outlet.
- The boiler is connected to the water supply using tees, sealant and gaskets. It is important to tighten the threads firmly, but not to overdo it.
- A special dropper is attached to the hole of the check valve to remove moisture.
Under no circumstances should the device be connected to the network until water has been filled into it.
Installation of a flow heater:
- Before installing the device, you need to make sure that the electric meter can withstand such a load. At the same time, do not forget about other electrical appliances used indoors.
- To connect the device to the network, you must ensure that you have a three-core cable of sufficient cross-section, specifically used for the water heater being installed. It is best to have an electrician do this.
- We install the mounts on the wall. If they are not included in the package, you will need to purchase them separately.
- We connect the device to the water supply and mixer. The main thing in this procedure is to seal all connections.
- Don’t forget to install a valve that can be used to shut off the water supply.
There are no particular difficulties here, but if difficulties arise, it is better to contact a specialist.
Gas water heaters
A cheaper alternative to an electric water heater are gas water heaters, in which water is heated by burning natural gas supplied to the house through a gas pipeline.
Undoubtedly, gas water heaters are cheaper to maintain, however, they are much more difficult to install and maintain.
The division of gas water heaters is similar. A flowing gas water heater , called a gas , heats the water pipes inside the water heater body. A storage gas water heater, called a gas boiler , heats a container of cold water to a certain temperature using the thermal energy of burning gas.
Geyser in the kitchen
Gas and electric water heaters can be mounted on the kitchen wall or on the floor of a special room. The name refers to this feature as a floor or wall mounted water heater.
Important! If you can still install an electric water heater yourself, then to connect it to gas you will need to invite a specialist from a specialized organization.
Gas water heater in the kitchen
