Proper plowing of the land using a walk-behind tractor, setting up and preparing the garden for plowing

Today, not only farmers, but also more and more owners of suburban land plots prefer to mechanize soil cultivation using walk-behind tractors. A large number of types of various mounted and trailed equipment allows these units to be indispensable assistants in almost all types of earthworks.

As for the plow, this device is not only in demand, but also necessary when cultivating the soil. In this article we will talk about plows for the Neva walk-behind tractor, which is popular in our country, which is widely used when cultivating small plots of land.

You can install the plow for this walk-behind tractor yourself

Setting up a walk-behind tractor

Working with a walk-behind tractor begins with setting it up. It depends, first of all, on the area of the plowed area, as well as on the quality of the soil. Some universal rules will help you set up your equipment correctly:

The recommended diameter of the lugs is 50-60 cm, and the width is 18-20 cm. If the dimensions are smaller than those specified, the equipment will not make it possible to make an even furrow; it will be driven on different sides.
It is preferable to choose a solid wheel rim so that earth does not accumulate on it.
The weight of the unit must be less than 70 kg, otherwise it will constantly slip.
The position of the machine itself when plowing should be such that its entire base is completely in contact with the soil. Otherwise, the plowing depth will either be too great, or, conversely, plowing will not work at all.
When attaching the plow to the coupling device, the fastening nuts are not fully tightened. This leaves the possibility of further regulation. Using just two pins, you can easily connect the plow to the mounting eyelet.

Installation

The quality of its work with the walk-behind tractor depends on how correctly the plow is assembled.

• To begin with, a ploughshare is welded to the metal plate that will become the blade.
• Next, the side pillar shield is attached.
• Then the spacer bar, base and stop corners are attached to it.

It is important that all parts fit together, otherwise the plow for the walk-behind tractor will not cope with its purpose.

In order to clearly see how various plows for walk-behind tractors work, it is worth finding a thematic video on the Internet. In this case, it will become clear how different plows function, and this will help you choose the optimal design for yourself. Only by using high-quality equipment can you count on good results.

Benefits of using a plow

Using mechanical tools to plow a field greatly simplifies farm work. According to statistics, the yield almost doubles if the field is processed using specialized devices.

The following are the advantages of using motorized plows:

saving time and getting better results by applying a minimum of effort;
additional loosening of the soil and subsequent fertilization using one tool;
uniform cultivation of the land and, as a result, improved structural quality and condition;
saturation of the soil with moisture and oxygen;
slowing down the growth of weeds through land cultivation.

The advantages of homemade “gadgets”

When making a homemade plow, you can get advantages that are not available in factory models. By creating a plow with your own hands, you can adjust it to the required values necessary for cultivating a certain soil on the site, for example, hard or soft. Such parameters may be different: the angle of inclination of the ploughshare, the width and depth of plowing of the field, and the efficiency of loosening.

If the engine power is taken into account when creating, the resulting product will not produce additional load on the motor cultivator, the wheels will not slip during operation, and plowing efficiency will be optimal. Moreover, if you make single-body or rotary plows with your own hands, the material can be adjusted to the required quality, and thereby increase the service life of such a unit several times. By making the plow yourself, you can provide the possibility of attaching additional “gadgets” for plowing the land.

Installing a plow on a walk-behind tractor

Regardless of the design features of the plow, its size and shape, it is attached to the walk-behind tractor with a special hitch. It can be universal or stationary. The first option is optimal due to the great possibilities for customizing the device.

The type of hitch does not affect the features of mounting the structure on motor vehicles.

You can attach a plow to a walk-behind tractor by following a simple diagram:

The unit is installed on an elevated position. You can use bricks or logs;
The plow hitch is attached to the towbar. Both holes on the devices must match completely;
The clutch on the towbar must be secured with a bolt.

Do not forcefully tighten the bolt when attaching attachments. A connection that is too rigid will negatively affect the quality of plowing the soil. When creating resistance during operation of the plow, it will be thrown a little to the sides. To avoid this, it is necessary to leave a horizontal gap of approximately 50.

How to prepare for work?

Preparing the unit for work includes installing lugs, as well as hanging and adjusting the plow.

Installation of lugs. These devices are metal wheels with a diameter of up to 60 cm and a width of 17-20 cm. Thinner samples are also available for sale, but it is not recommended to buy them. This is due to the fact that it is very difficult to make an even furrow with thin hooks: the walk-behind tractor will swing in different directions and it is quite problematic to cope with it in such conditions. In order to install the lugs, the unit is placed on a flat surface, the original wheels with rubber tires are unscrewed and the hubs are removed.

The hubs of the hooks are put on the drive axle, secured with pins and secured with cotter pins.

The hitch hubs are slightly longer than usual, so their use leads to an increase in the track width, which makes the walk-behind tractor more stable. After the hubs are securely fastened, lugs are mounted on them. When attaching metal wheels, you must ensure that the tread tapers forward. It is advisable to select hooks in such a way that after hanging them, the total weight of the unit is more than 70 kg. Otherwise, the machine will slip and the processing will be uneven and of poor quality. If you purchase lugs that are too light, you need to take care of additional weighting of the structure. To do this, you can purchase a set of additional weights, the installation of which will provide the required weight.

Installation and adjustment of the plow. The plow is secured using hitches that are attached to the unit using a king pin. It is recommended to make the connection of the hitch and the unit with a backlash of 5-6 degrees. If you fix the plow motionless, then when plowing it will begin to swing the walk-behind tractor from side to side, which is due to the uneven influence of the soil on it. When connecting the hitch to the plow, it is not recommended to tighten the nuts completely. This is due to the fact that there is an adjustment process ahead, during which they will have to be tightened and loosened more than once.

To make adjustments, you must install the unit on bricks or stacked boards. The height of such a structure should be equal to the plowing depth and be 20-25 cm. The lugs should be fixed, thereby ensuring complete immobility of the walk-behind tractor. Then the plow is positioned so that the entire length of the field board lies on the ground. In this case, the plow stand must be located strictly perpendicular to the ground and parallel to the inner end of the toe.

Then the slope angle of the field board is adjusted, while the distance from the nose of the plow (ploughshare) to the heel should be 3 cm. If the slope adjustment is neglected, then during operation the plow will begin to dig into the ground, the engine will overheat and work will have to be stopped. Next you need to adjust the track width. To do this, the right edge of the ploughshare is aligned with the inside of the right lug.

With this arrangement, the soil will be cut absolutely evenly, and it will become easier to operate the unit.

Starting the unit. Before starting a gasoline or diesel engine, you need to check the oil level and fill the tank with fuel. Two-stroke gasoline models run on a mixture of gasoline and motor oil, while powerful four-stroke models “use” pure gasoline of the A-92 and A-95 brands. When refueling a walk-behind tractor with diesel fuel, you should take into account the temperature conditions and fill in winter diesel fuel in the cold season. Also, before starting, you should check the functionality of the steering wheel, gas, reverse and clutch, after which you can start it.

To turn on a gasoline engine equipped with a manual starter, open the valve on the fuel tank and set the choke lever to the “Start” mode. Then, without turning on the ignition, perform 3 to 5 starter movements, after which the ignition is turned on and the engine is started. As soon as the engine starts, the choke is immediately switched to the “Operation” mode. On walk-behind tractors equipped with an electric starter, starting the engine is even easier. To do this, simply turn on the ignition, the electric pump pumps fuel into the carburetor and the engine starts.

Before starting the diesel engine, all air in the system is expelled with an electric starter, and after diesel fuel takes its place, the engine is started. If the engine is equipped with a manual starter, then simply open the diesel fuel supply valve, set the gas and press the decompressor. Then the starter is pumped several times, the decompressor snaps into place and the engine starts.

Mini, medium or heavy?

In order for plowing with a plow to be effective, it is necessary to choose the right equipment. When choosing, it is necessary to take into account, firstly, the area that will be processed with its help, and, secondly, the tasks that it must perform.

There are three types of walk-behind tractors:

light (mini);
average;
heavy.

Mini or light walk-behind tractors

Used to work in small areas, they are also called motor cultivators. The engine power of these devices is up to 4.5 horsepower.

Among the advantages of motor cultivators are:

lightness (weight does not exceed 40 kg);
low price (from 6000 UAH);
the ability to process hard-to-reach places thanks to the small grip of the cutter.

However, light walk-behind tractors do not work for a long time, since they have an insufficiently powerful engine, which quickly overheats, and do not bury themselves well in the ground due to their insufficient weight.

Medium walk-behind tractors

Unlike light ones, they boast rear-wheel drive and are great for working on large areas (up to 0.5 hectares). Weight varies from 45 to 65 kg, the cost of such equipment, on average, is 10,000–12,000 UAH. Engine power - 4.5–12 liters. With. Many models of medium walk-behind tractors can be equipped with additional equipment.

Main advantages:

presence of a front headlight and two gears;
the ability to attach a plow;
Compared to heavy ones of this type, medium walk-behind tractors are more mobile and easier to turn.

Among the weak points of monoblocks of this class are the processing depth of up to 11 cm, which is insufficient for many crops.

Heavy walk-behind tractors

Suitable for professional cultivation of land on plots whose area exceeds 0.5 hectares, since they have an engine power of 12 to 30 hp. With. and many advanced features. The cost of heavy walk-behind tractors is at least 12,000 UAH. The ability to attach a trailer or plow is one of the main advantages

walk-behind tractors of this type. They break through easily and cover the area many times faster than motorized cultivators.

Heavy walk-behind tractors have additional options: the ability to adjust the pneumatic wheel and steering wheel (higher and lower), reverse. Noticeable disadvantages are bulkiness, which requires a lot of force to turn the equipment; the need for reinforcement, because under high loads, the cutter or steering handle may break.

DIY disc plow

A disk plow on a walk-behind tractor or a hiller plow is a special device used for cultivating the soil before planting tuber crops.
Lays furrows for planting potatoes, beets, celery, and hills them. Below is a diagram and drawing of the hiller

Its structure includes:

2 – disks;
3 – fist;
4 – bracket;
5 – axis;
6 – scraper;
7 – driving beam;
8 – screed;
9 – handle.

The number 1 indicates the work area.

Discs can be taken from an old seeder. Their installation is carried out at an angle to improve the productivity of arable work. Attaching the hiller to the walk-behind tractor through the hitch bracket. The T-shaped plow leader is screwed to it with bolts and a stopper. At high speed, the hiller may begin to slip. Therefore, you need to work with it only at low speeds or with paired wheels.

According to another instruction, the disk plow for the walk-behind tractor begins to be assembled by cutting out an equilateral corner. The toe is welded to it, and then through the thrust bar and the heel. The discs are mounted on special hinges, which are welded to ensure their symmetrical position to the common axis.

What affects the cost of plowing plots?

When you need to plow the land with a walk-behind tractor or cultivator, you want to know what the cost can be. Managers guide you by prices without seeing your site. The final payment is made by our specialists on site. They can go to the region to assess the property in advance, if required.

Several factors influence the cost:

the purpose of plowing is for planting, for a lawn, before winter, etc.
area and geometry of the site;
soil composition – black soil, sand, clay;
additional wishes of the customer.

How to plow the ground with a walk-behind tractor

Working with the device on site may vary depending on the tasks assigned. You need to know where to start, how to assemble the device correctly, what equipment to install and what efforts to apply.

Installing wheels

Plowing the land with a walk-behind tractor begins with assembling the device. In order for it to be assembled correctly, you must first attach the wheels, and only then install the plow. For optimal stability, we recommend that the wheels of the machine have a diameter of 50 mm or more, and their width is at least 20 cm. If these proportions are not met, it will not be possible to plow the soil efficiently, since the necessary immersion will not be ensured. Each of the two indicators indicated above is based on clear engineering calculations. For example, if the wheel width is insufficient, the entire device will roll in both directions when moving straight. If the diameter is incorrectly selected and the wheel is too small, the distance between the soil and the gearbox will be insufficient, which will lead to poor-quality plowing.

When choosing such an important attribute for a walk-behind tractor as a wheel, it is important to remember the rim. It is best if it is solid. If there are lug ribs, earth will get into them, dry out and prevent normal rotation.

Adjusting the plowing depth

Before plowing the plow, it is necessary to set its depth correctly. Different types of settings apply to different devices. So, for example, for plows with the PTK-9-35 index, the setting is as follows.

Under both left wheels, transport and pneumatic, special liners are placed, whose height is slightly less than the required depth by 2-4 cm.
Using the screw mechanism of the support wheel and the thrust screw of the left pneumatic, the body is lowered so that the support plane rests on the platform. The right support wheel remains on the plane of the body.
To pass the first furrow, the right wheel of the support is raised using the adjusting screw to a height that is equal to V3 from the depth set for plowing.
On the subsequent furrow, the right wheel is lowered to the level of the supporting plane of the body. During operation, the immersion depth of the plow is adjusted using the stop screw of the left pneumatics.

Plow PTK-9-35

Semi-mounted plow (index PLP-6-35). Plowing the site using this type of equipment is possible after setting it up. The plow frame is leveled using the screw mechanism of the support wheel, having previously placed a lining under the metal wheel. Often, the right-hand slanting mechanism for mounting the walk-behind tractor itself is involved in the alignment process. Each body must touch the platform with both the toe of the ploughshare and the heel of the field boards. In this case, the adjustable upper link is shortened to the limit.

Plow PLP-6-35

Mounted plow. Tilling the soil with a walk-behind tractor with a mounted plow requires careful debugging. The setup principle is generally similar to the previous point. The length of the top link at the attachment of the walk-behind tractor itself and its braces changes, then the frame is installed, but here it is worth remembering that this must be done strictly parallel to the site. The liner is placed under the wheel, which serves as a reference point, whose height corresponds to the required immersion depth with an error of up to 3 cm. During the first pass, the right brace of the walk-behind tractor suspension is reduced so that its first body is plowed to half the depth that was originally set. During the second pass, the distortion of the frame on the right brace is eliminated; this manipulation is performed in a transverse-vertical arrangement of the equipment.

In general, the process on tractors of different models and walk-behind tractors will not differ much from that presented above. Significant changes in settings are available for power regulators installed on heavy agricultural machinery. Here the wheel, which serves as a fulcrum for the plow, is lifted up or completely removed. To activate the regulator, the hatch under the seat is folded back, the lock is rotated, inserting the shank into the corresponding groove. In this case, you need to rotate to the left. Each distributor handle is placed in the neutral position, and the GSV handle remains in the locked position. The handle responsible for the regulator moves forward. The longer the regulator handle moves forward, the greater the depth of the plowed surface. When the required depth of immersion of the plow is found, the position is fixed with the handle of the power regulator of the handwheel-limiter.

To check the quality of plowing, special control is carried out. A furrow meter is used for this.

Adjusting the angle of attack

Plowing a garden using a walk-behind tractor is impossible without precise preliminary adjustment of the equipment. The angle of attack, or, more simply, the inclination of the field board, is the inclination that demonstrates the level of the plowing plane relative to a flat surface. This angle is adjusted using a conventional handle with a screw mechanism. To make the adjustment, you must complete the following steps in the correct order.

Place the machine itself with the plow on the special stands mentioned above.
Unscrew the adjuster handle as far as possible so that the field board remains completely pressed to the surface (even small gaps are not allowed).
Then you need to start twisting the handle in the opposite direction until the back side is about 3 cm above the surface.

To make sure that the settings are correct, you need to proceed to plowing; at this stage it will be easy to determine whether the walk-behind tractor moves easily or rests heavily on the ground. If the angle of attack is large enough, the plow will begin to act as an anchor, thereby extinguishing the potential of the walk-behind tractor transmitted from the internal combustion engine, and accordingly, the efficiency will sharply decrease. This will lead to slipping and difficulty moving in the forward direction. If the angle of attack is insufficient, the required layer of soil simply will not be removed.

For high-quality plowing, it is necessary to make an even and clear straight line from one edge of the site to the other. All subsequent lines and the accuracy of the work performed as a whole will depend on this. To simplify the task, you can level the area with pegs and rope, at the same time clearly marking the boundaries and setting guidelines for plowing.

One wheel of the device must be placed in the furrow, the plow is oriented so as to remain perpendicular to the ground. The easiest way to achieve this is with a square. If it is inconvenient to make adjustments directly on the soil surface, you can place a stand that will correspond to the depth of the furrow. Once you have completed the setup process, you can move on to the second and third furrows.

We install the plow according to the track width

Even if the angle of attack has already been set, there is no need to rush to plow with a motorized cultivator. For competent and productive operation, the plow needs to stand on the soil surface not only with the heel, but also with the toe. This fact is easy to confirm even visually: if the stand is positioned vertically, it means that the setting has been carried out correctly. Heeling the plow will result in unnecessary pushing to the surface. When standing on its toes, the equipment will go deep into the soil.

At the moment of plowing, the load on the plow is not at all symmetrical, as it might initially seem. During operation, the walk-behind tractor will constantly open to the right. Usually the most difficult step is plowing the first furrow. For such needs, a stretched cord or a drawn line is used, which serves as a guide. The first furrow should be shallow - about 12 cm. Further work will be easier, because the right wheel of the walk-behind tractor will already go along the furrow.

It happens that the hitch beam is quite long. In this case, it is best to plow using a fulcrum, such as a wheel. It will help create the required depth of the plow. Typically, such a device can roll on both sides, both left and right.

Advice! It is much more convenient to work with a walk-behind tractor if you move both handles to the left - this will help you easily move along the unplowed side.

Recommendations for plowing various areas of land

Plowing virgin soil or any large piece of land where agricultural work has recently been carried out is not an easy task. Experts first of all recommend focusing on the shape of the existing site.

A rectangular area is best plowed in a circle;
Square plots are best plowed in a zigzag pattern.

In both cases, it will be more convenient to form a bed along the entire perimeter, placing them parallel to each other. In the future, this can significantly simplify the work of digging and planting.

It is not uncommon for the soil to be too hard. This problem cannot be solved in one go. It is best to plow in stages, first with heavy equipment (a walk-behind tractor with a rear adapter works great). With each subsequent treatment the soil becomes softer.

Advice! It is best to plow the soil when it is saturated with moisture. This leads to another recommendation: it is advisable to plow after precipitation or after the next watering.

Soil layers lend themselves well to processing using a walk-behind mill. To carry out such manipulations, you should drive over the same place several times, immersing the equipment more and more into the soil.

Many users wonder how many acres can be processed with a walk-behind tractor? Experts and experienced farmers say that using a walk-behind tractor, you can easily cultivate a plot of up to 10 acres. However, with perseverance and hard work, some cultivate entire hectares of land.

Installation of ground hooks

Ground hooks are special wheels on a walk-behind tractor for plowing. Their diameter is usually 50 cm, width - 18 cm. If you take a smaller size, the equipment will “swing” to the sides and it will not be possible to make an even furrow. You need to place the walk-behind tractor itself on a flat surface, remove the main wheels and install in their place the hooks prepared with the axles. Only after this they proceed to installing the plow.

Hanging and adjusting the plow

Various types of couplings are used for fastening. First of all, the plow itself and the couplings are connected. It is fastened on one side, the play on the horizontal plane should be about 5-6 degrees. It's important to remember a few things. If you fasten on both sides (with pins) or do not set the backlash, then the connection turns out to be too rigid, and this is a typical mistake.

The plow is then attached to the equipment's coupling device. The nuts should not be tightened tightly - adjustments still need to be made. It is better to perform this action with an assistant. The walk-behind tractor is installed on stands of about 25 cm (they can be made from scrap materials).

The ground hooks are fixed, the walk-behind tractor must stand level and not overweight, this is necessary for high-quality plowing. The plow bed is positioned so that the heel is parallel to the surface of the ground; adjustment is made using bolts. After the stands are removed, the plow blade is lowered to soil level, its rear part should be approximately 2.5 cm higher.

Starting a walk-behind tractor

Many owners have no idea how to properly start the engine. Most don't even touch the instructions. However, you can make mistakes that will lead to breakdown of the entire device, and repairs are often expensive.

First check the oil and fuel levels. Two-stroke engines should be filled with gasoline diluted with oil; the required proportions are given in the description of the device. Gasoline is used grades A-92 and A-95. For diesel engines fueled with diesel fuel, you should take into account the temperature outside, and base your choice of fuel on this.

Before the launch itself, the clutch, reverse, gas, and steering wheel are checked. The choke lever is set to the “Start” position, about 5 movements are carried out with the starter. After the ignition is turned on, the engine starts, the choke is switched to “Work”. Next, they begin to cultivate the land with a walk-behind tractor.

How to plow with a walk-behind tractor correctly

The process is not difficult to understand. First, the first control pass is carried out at low speed. In this case, the device is tilted to the left. Afterwards the technique is tilted to the right and a second approach is made. The result is checked - the depth and quality of plowing. If necessary, adjustments are made.

When working, the right lug should not go beyond the furrow line; it is better to move it in the middle. When properly configured, the equipment operates smoothly, without jumps or sudden movements.

What attachments does the walk-behind tractor work with?

Any experienced farmer knows that with the help of a walk-behind tractor, cultivator or other motorized equipment, almost all agricultural work can be mechanized: starting with cultivating the land to prepare it for sowing and ending with transporting the harvested crop. Motor units have become universal due to the possibility of using a variety of attachments. In addition to moldboard and other plows, the following equipment has been created for processing plowed land and cultivating virgin lands:

Harrows are used to plow virgin soil, as well as for pre-sowing (spring) or post-harvest loosening (autumn) of arable soil to a depth of 7-14 cm. Using harrowing with a walk-behind tractor or cultivator, the surface is leveled, moisture is covered, and weeds are destroyed. The working parts of such agricultural implements are metal teeth or spherical disks. In this video you can clearly see how to properly plow with a walk-behind tractor and a homemade harrow. And also from there you can learn improvements for the harrow.

The hiller is used to hill up potatoes, cut furrows for sowing seeds, backfill planting material, and also sprinkle weeds directly in the row area. Hilling devices come in single-row and double-row, with fixed and adjustable working widths, distinguishable both by their design and their efficiency. Here is a video of how the Neva MB2 motor cultivator performs processing with a mounted two-row weeder-hiller.

With a rotary cutter you can plow virgin soil, carry out pre-sowing and basic cultivation of plowed land. This agricultural implement allows you to mill, cultivate the land and qualitatively prepare it for sowing. It is capable of not only plowing the soil, but also mixing it with fertilizer, crumbling large layers, crushing stubble particles, and leveling the sown area. Rotators for cultivation come in different types, depending on the number of cutting elements. This video shows how to actually plow a walk-behind tractor with a cutter installed on it, as well as cultivation.

A flat weeding cutter helps to trim weeds, split and cut grooves without turning the formation, plow and crush the soil. Flat cutters come in all possible working widths and processing depths, which allows you to choose them for specific processing conditions of agricultural plots and crops. This video demonstrates well how to carry out processing with a mounted flat cutter in practice (using the example of a Dnepr walk-behind tractor).

In addition to the listed removable tools designed to plow virgin soil and cultivate arable land, rakes, wood splitters, seeders, shredders, cultivators, rotary and segment mowers, shovels, sprayers, sweeping brushes, snow blowers, etc. are used with the motorized unit. Having a basic set of mounted agricultural implements, you can use a walk-behind tractor or a powerful cultivator to perform all kinds of economic tasks, in particular, pre-sowing plowing, sowing and planting crops, applying fertilizers, inter-row cultivation of crops, harvesting root crops, and seasonal harvesting of green fodder.

Features of virgin soil plowing

How to plow virgin soil correctly? For high-quality processing you will need:

Motoblock unit weighing at least 100 kg. If it is lighter, the plow simply will not budge.
A rotary plow, which includes a cutter, a gearbox for connecting to a walk-behind tractor, and transport wheels.
It would not be superfluous to use special weighting in the form of ballast.

The work of plowing virgin soil must be carried out in stages, each time going deeper and deeper. In addition, soil moisture will make it easier to work with.

Good to know! The direction of plowing needs to be changed every year, since the soil layer is constantly shifting.

Models of walk-behind tractors such as Neva, MTZ, Khoper, and Centaur are in great demand among gardeners. In addition to plowing, they also provide for other agricultural work.

Potatoes are often hilled with walk-behind tractors, that is, a hiller is used instead of a plow. It penetrates into the ground to a shallower depth, thereby differing from the first.

It is also used for harvesting. For this, a special canopy is used that raises the ground. Then it is poured through the grate, as if through a sieve, and only the root vegetables remain on the surface.

Leveling the area using a walk-behind tractor and cultivator

This type of equipment is suitable not only for agricultural needs. A cultivator or walk-behind tractor can be used for landscaping work. You can level your dacha plot with improvised means, a shovel and a rake, as well as with the help of utility equipment, but if the area is hilly or replete with stumps and a developed root system, heavier equipment may be required.

Leveling the area with a cultivator is only possible if there are minor unevennesses that can be eliminated without resorting to additional technical means (a tractor with a bucket, etc.). The walk-behind tractor is capable of diving a little deeper, but on average, the diving area reaches 15-17 cm. Further leveling of the area occurs with the help of a rake. The loosened soil should be evenly distributed throughout the area.

If the soil on the site is too hard, rocky, or if there are stumps that have not been uprooted, etc., it would be better to resort to the services of a tractor. It would be better to dig up solid objects, such as a large stone buried a considerable distance into the soil, or an overgrown rosehip bush deeply rooted in the area, using a regular bayonet shovel. Only after removing parts that interfere with loosening and removing large debris can you begin to work using a walk-behind tractor.

It is important to remember that operating a walk-behind tractor and cultivator on hilly terrain and other uneven terrain is associated with an increased risk.

Spring plowing

In the spring, the garden is also plowed. During this period, soil reservation is carried out. This work takes place immediately after the top layer of soil has dried sufficiently. For plowing large gardens, it is better to use a tractor cutter. At the same time, it is not at all necessary to plant it deeply. In this case, the soil is loosened safely, because all its beneficial bacteria remain absolutely unharmed.

Regardless of the time of year, you should definitely know how to plow the land correctly and what secrets this process has. There are both manual and mechanical methods of plowing the garden. For small areas it is not necessary to call a tractor. In this case, a walk-behind tractor will be sufficient. The appropriate technology allows for fairly deep plowing (up to 25 cm).

A tractor is necessary for large vegetable gardens. At the same time, the person who will manage it must have professionalism and appropriate experience. When choosing the type of tractor, it is necessary to take into account the properties of the soil itself. Sometimes the heaviest equipment simply cannot penetrate deep into the ground. Such tractors even sometimes sink in the soil, which is why plowing is not done properly.

Do-it-yourself plow to a walk-behind tractor from a horse-drawn tiller

An equally viable idea is to recycle an old horse-drawn plow into a walk-behind tractor.
A full description of the process is given in the video. A feature of all horse plows without exception is their heaviness, created by a bulky moldboard. If such a plow is installed on a walk-behind tractor without modification, the ground will not tilt. This is a big plus, since the horse plow share will not undergo any changes.

To make a plow from a horse horse into a walk-behind tractor you will need:

make your own blade, which is cut according to a pre-drawn drawing from a steel blank (3 cm thick). For accuracy, it is advisable to make a cardboard template;
after cutting, the stainless steel blade is given a special shape;
remove the horse blade and install a homemade one instead;
remove the handles that were on the vertical axis;
Instead, weld metal fasteners through which the plow will be hung to the walk-behind tractor.
If during field testing it turns out that the converted horse plow does not throw well, the ploughshare should be slightly bent so that it can cut deeper into the soil.

Features of autumn and spring plowing

As strange as it may sound for a city dweller, the main plowing of the soil is carried out not in the spring, but in the fall. It is called “chill” and is intended to prepare for the winter-spring season. Deep autumn cultivation destroys harmful larvae overwintering in the soil, the earth is abundantly saturated with moisture and oxygen. Timely work significantly increases soil fertility and ensures high yields, while simultaneously reducing the damage to crops by numerous diseases.

Spring deep plowing can have the opposite effect. The combination of humidity and warm air promotes the proliferation of bacteria, fungi and other parasitic organisms in freshly dug soil. Seeds that fall into such soil will either die or grow sickly and weak.

In spring, it is preferable to harrow the top layers of soil. Thanks to the grinding of the surface, all the moisture accumulated during the autumn-winter period will be preserved in the lower layers, and the earth will also be replenished with the necessary supply of oxygen.

It is advisable to introduce manure and straw into the cultivated lands in early spring, which has been resting for at least six months. Such organic components improve the quality, increase the looseness, aerobic properties and fertility of the soil. Beginning farmers should remember that fresh, unburned manure will do more harm than good - this fertilizer can only be applied during autumn plowing.

Types and design of walk-behind plows

The plow has a share with a special geometric shape and a heel for processing compacted hard soil.
As a rule, the plow design is collapsible, and the ploughshare itself is made of durable steel, since it bears the bulk of the load. After plowing, the soil must be treated with a cultivator. Each walk-behind tractor model has its own attachments. However, there are also universal models suitable for equipment from any manufacturer. Currently, you can buy three types of walk-behind plows:

Single-hull. As the name implies, the design has one ploughshare and is intended, as a rule, for cultivating light types of soil.
Negotiable. The overturning of the formation occurs thanks to plowshares made in the shape of a feather. This plow model makes it possible to plow harder types of soil and make their further cultivation easier.
A rotary plow, which is equipped with several working blades.

Common problems and their solutions

Remember that plows are structurally different from each other. The general adjustment process is similar, but the elements by which the adjustment occurs may differ. Before starting connection and setup, read the instructions that came with the device.

The same applies to the walk-behind tractor. Check the instructions to determine whether the wheels need to be replaced with lugs, and what diameter they should be. It is recommended to install weights on light and medium-class walk-behind tractors so that the unit sinks under the weight of the machine. If the plow is configured correctly, but the machine still slips, then the unit is too large for the walk-behind tractor of your power. This problem can be solved by installing weights.

When choosing a device, focus on the power of the walk-behind tractor. The heavier the machine, the larger the diameter of the plow you can install. Heavy diesel walk-behind tractors are equipped with two-body devices that increase the productivity of site processing.

The design of the plow is simple and understandable - the main thing is to pay attention to the unit itself and think sensibly when connecting it. Remember that the unit must be looked after in the same way as a walk-behind tractor. Clean your unit after plowing, try not to plow rocky soils and perform timely maintenance on your assistant.

Rotary plow: algorithm of actions

A rotary plow for a walk-behind tractor with a support wheel is considered a complex type of canopy due to its design. It is necessary to work on it with special care so that mistakes do not negatively affect the quality of tillage.

The rotary plow is manufactured according to a certain algorithm:

The cutter is a working part. For manufacturing, you need to prepare a steel tube and metal plates. The latter are welded to the pipe for subsequent grinding of the soil and throwing it to the side;
Manufacturing the frame for the gearbox. It can be of any shape, the main nuance is that the frame must protect the gearbox from moisture, debris, and external damage;
You will have to buy a gearbox. It is connected to the gearbox of the unit;
The rotary plow is quite large in size, so you need to install wheels. Old motorcycle wheels will do just fine.

This design will last a long time. It is important to promptly change the oil that lubricates the gearbox to prevent breakdowns.

Timeliness and quality of plowing land with a tractor

Timely plowing will help retain moisture in the soil. When working, the soil should not be smeared onto the plow and fall off in large pieces, which is possible with high humidity. Or spray and break in low humidity. When cultivating wide layers, loosening is incomplete when the plow takes a layer that exceeds its normal work. In turn, if you are late and allow the soil to dry out, this will greatly affect future yields. That is why choosing the optimal time for plowing is one of the most important tasks for a landowner.

Our company has extensive experience in carrying out field work (we have cultivated over 10,000 hectares of land), and we will be happy to tell you the required time not only for plowing, but also for any other type of land cultivation.

Vegetable garden cultivation – cultivators to help farming enthusiasts

A garden, vegetable garden and lawn are attributes of country life, but the scale of plantings varies depending on the preferences of the owners. Some people are more attracted to trees, shrubs and lawns, and a modest corner is allocated for several beds. Some people, on the contrary, prefer garden beds and enjoy earning “penguin color” among the vegetable expanse. But in both the first and second cases, the land needs regular care, and the yield will largely depend on the quality of pre-sowing tillage. Farming requires a lot of labor, and the larger the area, the more difficult it is to maintain it manually. If you use specialized equipment, much less effort will be required, and the speed of work will increase. Let's consider which technique will be a reliable help.

Content

Safety precautions

The safety rules recommended for compliance when using a motor cultivator are not complicated.

You should adhere to the following rules:

Operation may only begin after full reading of the instructions supplied with the device;
It is prohibited for children to use the device, as well as persons who do not have experience in handling the device;
during plowing, it is important to eliminate the proximity of any animals and other people;
work should be carried out in closed clothing with long sleeves and closed shoes without dangling elements or in special equipment; It is better to choose high shoes, for example, boots or ankle boots, the toe of which is covered with a metal plate; We must not forget about gloves, mainly in the case of cultivating difficult soils, as well as safety glasses;

During operation, it is necessary to keep your hands and feet away from rotating elements, and also maintain balance in relation to the forward and reverse handles; they cannot be raised at the same time, since one must always remain lowered;
Vibrations occurring during operation signal the presence of breakdowns; in this case, the engine is stopped, cooled and the problems are eliminated if possible; most often the problem is a weakened fastening, which is easy to normalize;
If you have a model with reverse gear, it is important to adhere to one simple rule: before changing direction, you should wait until the cutters come to a complete stop.

You can learn more about how to properly plow with a motor cultivator in the following video.

Principles of self-adjustment of inventory

The next problem that land owners face is how to set up a plow on a walk-behind tractor? The efficiency of the equipment and the speed of tillage depend on the correct adjustment.

After you finish installing the plow, start making adjustments. In this case, take into account such factors as the coincidence of the longitudinal axis of the garden equipment and the regulator, as well as the vertical position of the machine bed.

In order to increase the efficiency of tillage, you can use an axle extension and metal wheels with weights. The walk-behind tractor itself should not have a thin stand, a short blade, or a thin body sheet made of low-quality steel. A technique that does not have such flaws and has sufficient horsepower will be a good assistant for cultivating the soil with a plow.

How to choose a plow for a walk-behind tractor

When choosing a plow, pay attention to the technical characteristics of your walk-behind tractor. For processing small areas, a single-body plowshare unit is suitable, and if you are the owner of a heavy diesel walk-behind tractor, then you can connect a double-body device, which will speed up the process of cultivating the land twice as much as a single-body unit.

Single-body mounted plow SCOUT PL-130

The SCOUT PL-130 single-body plow is connected to a single-point attachment to mini-tractors and walk-behind tractors with a power of 10 hp or more. With.

The unit is equipped with an enlarged steel ploughshare, and the design itself is made reliably - you can forget about sharpening the ploughshare. To regulate the plowing depth on uneven terrain, a limit wheel is installed. The plow is designed for processing heavy, loamy soils and virgin soil.

When working with the floating mode of the hydraulic distributor, the device must be weighted.

Single-body mounted plow SCOUT PL-130 HYD with scoring disc

The SCOUT PL-130 HYD single-furrow plow is equipped with a scoring disc for more efficient work on turf soil. The unit is connected to mini-tractors and walk-behind tractors with a single-point attachment mechanism. The working part is made of reliable steel.

The angle of attack of the plowshare is adjusted using turnbuckles. The limit wheel regulates the plowing depth. The trimming disc is designed to trim plant roots during plowing, which increases the productivity and quality of plowing.

To plow heavy soils and virgin lands, you need to install weights on the equipment: 80 kg in the front and 60 kg in the rear.

Double-furrow mounted plow SCOUT PL-225

The double-furrow plow SCOUT PL-130 is the only two-furrow device that is connected to a walk-behind tractor. The unit is secured using a single-point mechanism. But for work you need a walk-behind tractor or a mini-tractor with a power of 15 hp or more. With. The base of the plow is a triangular frame with turnbuckles that adjusts the horizontal and vertical position. The plowshare body is adjusted using a stand. The plowing depth is controlled by a limit wheel.

Sources

https://MoyMotoblok.ru/rabota/vspashka-zemli-motoblokom-plugom-i-frezami/
https://tokar.guru/stanki-i-oborudovanie/motobloki/kak-pravilno-pahat-zemlyu-podgotovka-motobloka-i-ogoroda-dlya-vspashki.html
https://sdelai-lestnicu.ru/stroi-tehnika/kak-pravilno-pahat-plugom-na-motobloke-kak-otregulirovat-glubinu-vspaski-zemli-nastrojka-motobloka-dla-pahoty-plugom
https://stroy-podskazka.ru/motobloki/pravila-vspashki/
https://zapchasti-isuzu.ru/marki-specavto/kak-pahat-ogorod-na-traktore.html
https://remont-dmb.ru/service/vspashka-zemli-motoblokom/
https://tehnika.expert/dlya-sada/prochaya-sadovaya-texnika/kak-pravilno-vspahat-zemlyu-motoblokom.html
https://mzoc.ru/selskohozyajstvennaya/kak-pahat-motoblokom-s-plugom.html
https://kamuflyzh.ru/tehnologii/kak-pahat.html
https://vospari23.ru/kak-pravilno-pahat-ogorod-motoblokom-s-plugom/
https://avtovishki-v-arendu.ru/spetstehnika/vspashka-ogoroda-motokul-tivatorom-pravil-naya-tehnologiya-i-sovety-ekspertov.html

[collapse]