A practical and economical option for heating large and small rooms in the absence of centralized heating is a gas heat gun. Its use is justified by its high energy efficiency and low cost of gas as fuel. Heat guns are produced by both domestic and foreign manufacturers, and the various characteristics of heating equipment allow you to choose a model for individual tasks. In this article, experts from the Sadpom online store will tell you how to choose a gas heat gun and recommend the best models for your home, garage, cottage, or warehouse.
Criterion No. 1: type of heating
Gas-powered heaters belong to one of two groups according to the type of heating. Indirect heating heat guns are designed to create an optimal temperature microclimate in residential buildings or rooms where people are temporarily located. In models of this type, the heat exchanger is designed in such a way that fuel is burned in it first, and then combustion products, which are highly toxic. For proper operation of an indirect heating heater, a separate exhaust pipe is not required - properly functioning ventilation is sufficient.
The direct heating heat gun differs from the first model in the principle of fuel combustion. Toxic waste is not completely destroyed in it, so natural ventilation is not enough here. To effectively remove combustion products, an exhaust pipe is provided, which is connected to a stationary chimney.
Important! The main advantage of indirect heating heat guns is their high level of efficiency, tending to 100%.
Remington REM 10 M
Characteristics:
- heating power (max) – 10 kW;
- heating type – direct;
- air exchange rate – 300 m3/hour;
- productivity – 8800 kW (kcal/h);
- fuel consumption – propane-butane 0.7 l/h;
- built-in temperature controller – no;
- burner, piezo ignition - included;
- weight – 4.1 kg.
Heater price: 4,990 ₽.
Product link: https://sadpom.ru/products/gazovaya-teplovaya-pushka-remington-rem10m/
Remington REM 10 M is a direct heating heat gun that runs on propane-butane and consumes up to 700 ml of fuel per hour. The choice of a gas heat gun for a summer house, warehouse or garage will be justified if there is high-quality ventilation that will effectively clean the air. The built-in overheating protection system will ensure high operational safety - the unit will instantly turn off in case of sudden overheating.
Advantages of the model:
- fuel consumption is lower than that of similar devices;
- included burner;
- exceptional reliability;
- high fire safety.
Flaws:
- not suitable for large areas;
- air exchange rates are lower than those of competitors;
- lack of thermostat.
Caiman VAL6 GN5
Characteristics:
- thermal power – 42.2 kW;
- fuel – natural gas, 2.8 kg/h at a pressure of 1.3 kPa;
- heating type – indirect, infrared;
- network voltage indicators – 220/230 V;
- ignition system – electric ignition;
- net weight (without fuel) – 49 kg.
The cost of the heat gun: 229,990 ₽.
Product link: https://sadpom.ru/products/nagrevatel-infrakrasnyj-gazovyj-obogrevatel-caiman-val6-gn5/
Caiman is a representative of a fundamentally new type of equipment, which implements an indirect infrared heating system. This is an expensive professional-grade device, which is recommended for heating business facilities, large warehouses, military and industrial bases, and construction sites. An infrared heating element emits a large amount of heat, the characteristics of which resemble solar energy - the rays do not just heat the surface, but penetrate inside, reaching the deep layers of objects.
Pros of the device:
- “radiant heat” for maximum efficient heating;
- competent fuel consumption system;
- neutralization of toxic combustion products - up to 20 times less carbon monoxide than direct-heated guns;
- low noise level;
- adjustable emitter angle.
Minuses:
- high price;
- massive and difficult to transport.
Important! Gas guns require not only fuel, but also power from the electrical network - the electricity is used to maintain the operation of the built-in fan.
Back to Contents
ElekonPower TT-15PS
Main characteristics
- Country of origin: Korea.
- Type - gas.
- Power - 4400 W..
- Heating area - 35 m2.
- Weight - 1.5 kg.
Detailed characteristics and prices
Review
gas heat guns are continued by the South Korean gas-powered model - ElekonPower TT-15PS. It is wonderful in everything: super-light weight (only one and a half kilograms), very economical gas consumption, safe and efficient design and... up to 35 square meters of a warm room in any frost! A very budget-friendly and at the same time reliable option, which appeared on the domestic market relatively recently. Simply attach the heater to a standard gas cylinder and 50 hours of uninterrupted operation is guaranteed. The device is safe for use in residential areas. It does not burn oxygen and automatically turns off when the flame goes out.
Pros:
- reliability and compactness;
- very low price;
- ease of use and safety.
Minuses:
- the need to purchase and place a cylinder.
Review from a real buyer:
I am completely satisfied with the heater, considering that I use it in the fall at the dacha. I alternately cook and warm myself on one cylinder - economically and quite safely.
Back to TOP 10
Criterion No. 2: equipment power
The consumption of fuel, electricity and the rate of space heating will directly depend on such a key parameter as the power of the installation. To choose the right gas heat gun for a garage, private home or warehouse, you need to assess the area of the room that needs to be heated. Obviously, low-power gas guns cannot cope with heating large rooms. And vice versa - owners of small rooms do not need to overpay for a powerful premium unit. When calculating power, Garden Assistant experts recommend focusing on the following principle: for every 10 m2 of space, from 0.8 to 1.4 kW of a heating device is required.
Herz G10
Specifications:
- thermal power – 10,000 W;
- fuel type – propane-butane;
- available for temperature adjustment – from +5 °C to +55 °C;
- air flow speed – 300 m/hour;
- fan power – 30 W;
- fuel consumption – 0.85 kg/hour;
- built-in options - overheat protection, digital display, thermostat, auto-ignition;
- weight – 5.34 kg.
Device price: 4,000 ₽.
Link to the product:
A lightweight and compact heater will be an excellent alternative to a stationary heating system and will not take up much space. Despite its small dimensions, the device will successfully cope with warming the air in large rooms, and the thermal curtain effect will prevent heat loss. When the set temperatures are reached, the built-in thermostat will turn off the heat gun, thereby saving propane-butane.
Advantages of the model:
- sufficient power to maintain heat in rooms of different sizes;
- the presence of a temperature regulator, thermostat and electric ignition;
- quick heating of the air, taking no more than 20 minutes;
- ease of movement;
- affordable price.
Disadvantages indicated by users in reviews:
- short gas hose.
Master BLP 73 M
Characteristics:
- thermal power range – 49,000-73,000 W;
- productivity (air exchange) – 2300 m3/h;
- fuel consumption – 5.02 kg/h;
- heating principle – direct;
- control type – mechanical;
- fuel type – liquefied gas;
- power consumption – 218 W;
- weight – 15 kg.
Model cost: 30,100 ₽.
Product link: https://sadpom.ru/products/gazovaya-teplovaya-pushka-master-blp-73-m/
Don't know which gas heat gun to choose for heating a large warehouse, production workshop, construction site or workshop? A model from Master, whose power is a record 73 kW, is ideal for your needs. The device will help you quickly organize a portable heating system with high reliability, and will also become a faithful assistant to specialists installing suspended ceilings.
Advantages of the device:
- high power;
- possibility of connecting a room thermostat;
- safety valve that shuts off the gas supply in case of leakage;
- gas hose and regulator included;
- durable housing with a long service life;
- ability to control power.
Minuses:
- significant fuel costs;
- relatively high cost.
Back to Contents
Popular manufacturers
In the 90s, the main leaders of the Russian market in the production of heat guns were Western Europe and Asia. In the 2000s, Russian companies began to appear that produce climate control equipment. Now there are a huge number of domestic brands that confidently compete with their foreign colleagues, while remaining in the low price segment. Here is an overview of several leaders in the production of climate control equipment:
- Resanta , a Swiss brand founded in 1932, remains a leader in the production of heaters in 2021.
- Ballu is a leading Thai manufacturer of air conditioning equipment for the home and industry, opened in 1980, which covers the whole of Eurasia and is known even in North America. The products are applicable for garages, cottages, and industrial premises.
- Frico is a European company that produces products that undergo strict AMCA and ISO quality certification.
- Master is a manufacturer of air treatment systems for both large and small areas. The master offers a wide range of heat guns.
- Kraton is a Russian brand that has the best price-quality ratio, as it offers budget equipment that meets all European quality standards.
- Zubr is another Russian manufacturer of construction tools and equipment that has its own laboratory for pre-sale testing of products.
- Interskol is the only brand in the CIS in its niche that is officially recognized by the EU.
- Sibrtech is a Russian trademark that takes into account local operating conditions during production. The products are famous for their high strength and reliability.
IMPORTANT ! Also worthy of attention are companies such as Caliber, Big Dutchman, Wester and Remington.
Parameter No. 3: fuel consumption
Although liquefied gas and propane-butane are considered budget fuels, some models of gas guns consume an unreasonably large amount of energy even with little “exhaust”. In order for heating equipment to justify the investment in it, pay attention to such a parameter as fuel consumption. It will directly depend on the power of the heater, but even among powerful models you can choose economical options with minimal gas consumption.
Important! Gas heat guns can operate effectively on both bottled liquefied and natural gas from the central pipeline.
MasterYard 15M
Specifications:
- thermal power – from 10 to 16 kW;
- fuel type – bottled or main gas;
- fuel consumption – 1.07 kg/h;
- productivity – 300 m3/hour;
- power supply voltage – 220-240 V;
- ignition type – piezoelectric element;
- net weight – 5 kg.
Price: 6,490 ₽.
Product link: https://sadpom.ru/products/gazovaya-teplovaya-pushka-masteryard-15m/
The presented model combines excellent technical parameters with low fuel consumption and a reasonable price. The model can be used for agricultural, domestic and industrial needs - its power is enough to heat large spaces, the volume of which reaches 655 m3.
Advantages of the device:
- stability of operation;
- optimal ratio of heat output and gas consumption;
- durability;
- well-thought-out protection system;
- compactness and mobility.
Flaws:
- high repair costs;
- inappropriate installation in small living rooms.
Back to Contents
Purpose of gas heat guns
It is important to understand the purpose of gas heat guns, since natural or liquefied gas is used as fuel, which is not suitable for every homeowner or entrepreneur. Here are three areas of application of such equipment:
- Heating of industrial premises - in this area, these units are very popular, as they demonstrate high efficiency and cover a large heating area.
- Preventing humidity in warehouses or workshops - gas heat guns also perform well in this case.
- Construction work and repairs - this area includes both commercial activities and the everyday needs of ordinary people.
REFERENCE . Compact dimensions and convenient shape are the unconditional advantages of the device.
Other criteria influencing the choice
In addition to the technical parameters described above, before purchasing a gas gun, it is recommended to evaluate other criteria that will affect ease of use. These include:
- Noise level is an important factor when a heater is purchased for residential premises. The noise level acceptable for human perception should not exceed 35-40 dB. Otherwise, being in a building with a very loud fan will be uncomfortable.
- Security system - a durable metal body, a thermostat, a flame controller and a self-shutdown option will allow you not to worry about a possible fire even when the gas gun is unattended.
- Type of design - if the unit is purchased for buildings where centralized heating is not planned, then you should opt for a stationary model. A mobile heater is good as an alternative source of heat - it is easy to move and install in any convenient place, directing air flow in the desired direction.
- Ignition system - the manual ignition method is not always convenient, but is characterized by increased reliability. Piezo ignition is considered a more “advanced” mechanism - a spark is generated by simply pressing. But in some cases, the piezo may not work the first time, and high humidity can damage the element.
- Temperature control and thermostat - allow you to maintain a constant temperature in a heated location and adjust the operation of the device to individual needs, changing the values depending on weather conditions.
Analyzing the models and designs of gas heat guns, we can come to the conclusion that when choosing a suitable installation, you should focus on parameters such as type of heating (direct/indirect), fuel consumption and thermal power.
Consider the area of the heated room, pay attention to additional options that will make the process of using the devices comfortable and as safe as possible. Return to list of articles
How to connect and use a gas heat gun
First of all, it would be useful to study the instructions, as it contains all the nuances of connection and use. It is recommended to carry out assembly based on the manufacturer's instructions in the instructions. Here are a few situations in which it is prohibited to turn on a gas heat gun:
- when there is a concentration of large amounts of dust in the air;
- in the presence of explosive vapors;
- when the outlet is blocked by any obstacle.
When turning it on, it is first important to check the ventilation of the room and the presence of oxygen in it. Next, you need to check the tightness of the connection with the gas cylinder, for example, you can use a soap solution. Ignition occurs in strict sequence. First of all, the main switch must be pressed, which will cause the engine and fan to start. Next, you need to press and hold the gas valve button and press the ignition button several times. When a fire starts, the button must be held for another 15–20 seconds, and then gradually released.
Patriot GS 30
Main characteristics
- Country of origin: USA.
- Type - gas.
- Power - 30.2 kW.
- Productivity - 700m3/h.
- Weight - 6.8 kg.
Detailed characteristics and prices
Review
Quite a powerful gas heater in a classic round case, on a stable platform. It is perfect for both heating residential and improving the climate in office and commercial premises, and will become a faithful assistant on country trips. High performance, excellent power and small dimensions are the optimal set of advantages of the American model Patriot GS 30. By the way, this “baby” also consumes very little gas.
Pros:
- practical design;
- safety and efficiency;
- affordable price.
Minuses:
- a good ventilation system is needed in heated rooms
Review from a real buyer:
I bought this gas heater for heating in a small workshop. The area of the room is only 12 square meters and within 10 minutes I felt like the tropics. Everything works perfectly, almost no noise, no smell. I recommend it.
Back to TOP 10
How to combine two cylinders into HBO? Implementation options
- The first method is to install two separate cylinders with their own air pumps. This option is less convenient, but easier to implement. Two cylinders are installed, which are connected through a tee to the central line leading to the reducer. Before inserting into the central highway, you can install one solenoid valve, although many argue that one is enough.
- The second option is to install two gas tanks with one VSU. This option is more convenient, since gas cylinders will be refilled through one device. The connection to the VSU is made through a tee, while some installers remove one multi-valve so that the second tank is filled more fully and acts as an additional tank, while the two tanks are perceived by the system as one. But I would not recommend taking risks by removing the second multivalve; this smart and multifunctional unit is very important.
There are other options, but, in my opinion, these two are the most optimal. The only thing you should remember is that the installation of gas equipment, as well as cylinders in particular, should be done by a professional. Any, at first glance, little things can lead to dire consequences or at least to incorrect operation of the gas equipment. Remember this!
If you know of other options for installing two cylinders in the HBO system, tell us about them in the comments, I will be very grateful.
Bye everyone, thank you for your attention, and see you again at HBOshnik.
About miscellaneous...
Rules of communication in the forum
| Before you ask a question! How to correctly ask questions in the forum and use site materials. |
| Moscow time 19:17:44 | Your local time | Vladivostok time 02:17:44 |
| Author: Sportsist (—.74.pppoe.mari-el.ru) Date: 13-11-15 02:42 The question is that the standard gearbox of the gun has a thread, but the cylinder on the farm was found not with a thread, but with a valve. The cylinder reducer of the RDSG type produces very little pressure - the gun does not even light up. Maybe throw all the guts out of it? Or is it not possible to connect this way? The valve cylinder is more convenient to use - when several times a day you need to separate the gun and the cylinder. |
| Author: Elgavchanin-1960 (—.tomtelnet.ru) Date: 13-11-15 03:00 “”””” The cylinder reducer of the RDSG type produces very little pressure - the gun does not even light up. Maybe throw all the guts out of it? “”””” I would not recommend doing this, without a gearbox - it’s equivalent to doing it directly, go out into the countryside and try it, you’ll see. what will come of this, but seriously, it’s easier to buy a new gearbox without a valve than to look for adventures, I have a 10 kW gun - five years like clockwork. |
| Author: Sportsist (—.74.pppoe.mari-el.ru) Date: 13-11-15 03:27 can you imagine a valve cylinder? NOT threaded?? There is only one type of gearbox for it |
| Author: s494 (89.179.209.—) Date: 13-11-15 03:57 Isn’t it possible to unscrew the valve and screw in the threaded tap? True... I had an old cylinder with a diaphragm valve, I decided to change the valve, I couldn’t unscrew it myself, I gave it to a friend, at the enterprise he clamped the valve in a vice and turned it by the cylinder... he tied the lever to it. Changed it - and that's it. So you need to transfer the valve to the tap. |
| Author: Sportsist (—.74.pppoe.mari-el.ru) Date: 11/13/15 04:17 and today 100% of all cylinders are made in a known place (((and mine from a scoop is completely new, I haven’t smelled gas ... |
| Author: s494 (89.179.209.—) Date: 13-11-15 04:23 And the “mother” to the valve is also from a scoop? Over time, it does not grip the valve well)))))))))))) and leakage occurs during use. |
| Author: fedot68(Kaluga) (—.opera-mini.net) Date: 13-11-15 04:47 s494 wrote: > And the “mother” to the valve is also from a scoop? > Over time, it does not grip the valve well))))))))))) > and leakage occurs during use. This is exactly how the neighbor in the dacha died. Antonina Fedorovna was then about 80 years old. She was badly burned. And she died in the hospital. In addition, the valve-mounted gearbox is non-separable. I mean, assembled on a rolled hoop. Maybe it would be easier to turn the cylinder valves to “normal”? It's not as difficult as it seems. |
| Author: Sportsist (—.74.pppoe.mari-el.ru) Date: 13-11-15 05:28 you will laugh - but “mother”, i.e. The gearbox is also new and made from a scoop. I just filled the 27L cylinder all the way, and then it turned out that the gun didn’t burn with it. What should we do now with the gas inside it??? |
| Author: fedot68(Kaluga) (—.opera-mini.net) Date: 13-11-15 05:40 The sportsman wrote: > you will laugh - but “mother”, i.e. The gearbox is also new and made from a scoop. I just > filled the 27L cylinder all the way, and then it turned out that the gun didn’t burn with it. What > should we do now with the gas inside it??? There is one of my favorite phrases. It infuriates some narcissistic idiots (there are many of them): “Before making responsible decisions, it is useful to think in the place that NATURE intended for this” (c) (Konstantin Natanovich Borovoy) |
| Author: fedot68(Kaluga) (—.opera-mini.net) Date: 13-11-15 06:08 By the way. “during it” (“late perestroika”), kits for weeding pigs and other things were sold in hardware stores: A nozzle instead of a reducer for the valve of such a cylinder, a hose for it and the burner itself. I even had one :-)) The principle of the device is simple Instead of three clamp balls, there are three screws. The “receiving mouth” itself, obviously with a “pressure” and a seal “in a circle”, but the pusher immediately pressed, or moved out synchronously with the twisting of the central valve (opening the gas) - for the life of me, I don’t remember Still, changing the valve is faster, safer and more reliable. Even taking into account the killed toad due to the release of 25 liters of gas. |
| Author: Slavyanin (—.broadband.corbina.ru) Date: 11/13/15 06:14 My neighbor unscrewed the tap on a small cylinder, put a pipe on a 1.5 meter key and unscrewed it, the thread there is tricky, with a cone. |
| Author: deniss P80-48AA (—.84.f.pppoe.atknet.ru) Date: 13-11-15 17:34 Kvasnik how to connect, for example, a Soviet 5L cylinder, you take a regular “reducer” like this with a reversible flag on the “top” and from it there is a hose to this burner heater and everything is the same with a 50l cylinder, naturally there is the same as a stove through a reducer, minus probably one is not there, turn down the gas, so it’s better to look for a reducer with a valve at the outlet so that the gas at the burner is turned down, and so when Dad was looking for a frog with adjustment; they were on sale only for the cylinder-frog threaded connection, so he took a 5L cylinder to the gas trucks so that they could replace the cylinder valve with a valve. |
| Author: Elgavchanin-1960 (—.tomtelnet.ru) Date: 13-11-15 22:56 “”””” can you imagine a valve cylinder? NOT threaded?? There is only one type of gearbox for it: “”””” Then it’s easier to buy a cylinder with a thread for a regular threaded reducer and calmly use the gun, rather than risk your health for 350-400 rubles. |
| Author: Sportsist (—.74.pppoe.mari-el.ru) Date: 11/14/15 02:33 people, I wonder HOW can you detect the inoperability of a gun with this cylinder and gearbox without refilling the cylinder??? I refueled it, tried it, it doesn’t light up. As for venting, it seems to me that this is more dangerous than using this gearbox. |
| Author: s494 (89.179.209.—) Date: 14-11-15 07:13 It was necessary to fill five liters. I think the gun won’t work with such a gearbox, there won’t be enough pressure. Once again: for a gun the pressure should be 1.5 bar. Link. Your reducer has an output pressure of 0.0036 MPa. Link. 0.0036 MPa is 0.036 bar Link. And you need 1.5 bar!!!! |
| Author: s494 (89.179.209.—) Date: 14-11-15 07:23
Well, the gun will not work with such pressure. |
| Author: s494 (89.179.209.—) Date: 14-11-15 07:41 This is the kind of gearbox you need. BPO Link. But even then not everyone. Here's the link. it is 0.3 MPa = 3 bar = 3 kg cm2 But this one is on the verge of working at all, Link. it is 0.13 MPa = 1.3 bar = 1.3 kg cm2 Look at the performance characteristics of your gun, how much operating pressure there is. And select a reducer based on this pressure. And bleed the gas from the cylinder through a reducer from a hose somewhere on the mountain in the breeze: gas-propane goes down and change the tap. Or buy another cylinder with a normal tap. |
| Author: Sergeich Nagatinsky (213.87.145.—) Date: 14-11-15 07:54 Guys, let's put an end to all this. 1. The gun operates from 1.5 bar; household gearboxes for gas stoves will NEVER allow it to work. 2. The collective farm when working with gas is terrible idiocy. 3. For the vehicle, a number of tips: - use the cylinder with the old nipple outside (do not place it indoors!!!!!) on a gas stove, etc., then replace the valve or take it to a ferrous metal. -gun - only the correct reducer for its pressure. – don’t worry about 27 liters of gas. It looks like you haven’t experienced any fires or explosions yet... |
| Author: Khoper (—.san.ru) Date: 14-11-15 15:54 These cylinders are now in ferrous metal like dirt, I recently handed over 3 of them, almost unused, my mother sold the dacha, there was nowhere to put it. Here they sell it for 300 rubles, then they accept it for 100 rubles by weight. |
| Author: Yelgavchanin-1960 (—.tomtelnet.ru) Date: 14-11-15 16:14 The sportsman wrote: “””””…………….. As for venting - it seems to me that this is more dangerous than using this gearbox “”””” Five points! Leaving this cylinder alone (or spending it on a plika) and buying the one you need is easier than becoming disabled. Here, two weeks ago, one of us decided to drain the remaining gas from the cylinder before refilling it (at the gas station we only refill empty ones) and I don’t know how it happened, but the jacket gave a spark when rubbing - the result is disastrous. |
| Author: bahader (—.opera-mini.net) Date: 14-11-15 17:19 In nature, there is a special adapter from a valve cylinder to a reducer. It is put on the side of the valve, “screwed” in the axial direction, for sealing, the rod is screwed in from above, pressing on the cylinder valve. On the side there is a threaded fitting for connecting the gearbox. |
| Author: Sportsist (—.23.pppoe.mari-el.ru) Date: 11/15/15 01:12 Thanks for the info about the adapter - where can I get it? I asked at the gas store - have you ever heard of such a thing? |
| Author: s494 (89.179.209.—) Date: 15-11-15 03:06 bahader wrote: > In nature, there is a special adapter from the valve cylinder to the reducer. > It is put on the valve from the side, “screwed” in the axial direction for sealing, > the rod is screwed in from above, pressing on the cylinder valve. There is a threaded fitting on the side for > connecting the gearbox. ======== Can I have a link? Very interesting because I have never seen anything like this. |
| Author: bahader (—.yota.ru) Date: 15-11-15 13:55 It is put on not from the side, but from above, (I haven’t used it for a long time, I forgot) it is fixed by sliding the bracket, the one at the bottom, which is in the form of tweezers, and behind it the lower part is screwed onto the upper one. We hold the upper part with our hand, it remains motionless, there is a gearbox and a hose on it. We open the tap - it opens “CLOCKLY!” arrow, and we use it... In Novosibirsk, filling a cylinder up to 50 liters with a valve is a huge problem, but you can exchange any valve at every corner. Therefore, I acquired such a thing five years ago, for the same purposes.. |
| Author: s494 (89.179.209.—) Date: 16-11-15 02:50 bahader wrote: > … ==== Thank you, I’ve never seen it before! Respect! ) |
| Author: fedot68(Kaluga) (—.opera-mini.net) Date: 11/17/15 01:56 And one more thing. 0.15-0.3 “points” is the gas pressure in the pipe that enters the house. And this is approximately the pressure that a person can, even “to hell”, give out with his mouth. 1.5 is already serious. Although the roof burner - “Aladdin” - works at exactly this pressure. Like a propane cutter, however... |
| Author: s494 (89.179.209.—) Date: 11/17/15 02:15 The diameter of the nozzle of the roofing burner and cutter cannot be compared with a heat gun. Moreover, the main thing in the cutter is oxygen, and the flammable gas there is purely for the “ignition”; with the support of oxygen, the metal burns even without flammable gas. A gas stove works with a “frog”, and only with one burner. You light the second one and the first one immediately goes out. It’s not for me to tell you. By the way, a roofing burner with which you can work “normally” without a gearbox at all! What is forbidden, really. |
| Author: Sportist (—.22.pppoe.mari-el.ru) Date: 11/17/15 03:43 with a coupling gearbox of the RDSG type, no gun (starting from 10) lights up. personally verified. The original gearbox of the gun says 1.5 bar |
| Author: vitgan (—.pppoe.mtu-net.ru) Date: 11/17/15 04:24 I apologize for interfering... I connected the gun in the garage at + temperature it works fine, but when it starts minus, then after a certain time of operation it starts freeze the cylinder and the gun works like a dead man's breath! Barely!!! How can anyone escape this problem? Heating the balloon is boring... |
| Author: s494 (89.179.209.—) Date: 17-11-15 04:45 I have a diesel heat gun, so it started to work poorly when condensation began to accumulate in the garage. I took the air in from outside and the problem went away. I cut off the bottom of a 10-liter plastic canister, put it on the intake, cut another hole for a plastic sewer pipe and brought the pipe into the ventilation square next to the gate. Propane cylinders in cold, humid conditions freeze over everything based on the level of gas in it. But you have a reducer, you can control the gas supply pressure, and if the pressure does not drop, then moisture in the air is preventing combustion. So I took clean frosty air from outside into the cannon, the garage began to dry out and the heat began to reach the most remote corners of the garage. |
ElekonPower TT-30PS
Main characteristics
- Country of origin: Korea.
- Type - gas.
- Power - 8800 W.
- Heating area - 70 m2.
- Weight - 3 kg.
Detailed characteristics and prices
Review
Looking for an inexpensive, efficient and economical heating option? Then the South Korean infrared gas heater ElekonPower TT-30P is exactly what you need. An excellent option for rooms up to 70 square meters! The advantages are double directional heating, original design, convenient format and very light weight. You can easily take such an assistant with you on any trip. Ideal for drying rooms with high humidity.
Pros:
- compactness and ease of use;
- versatility and safety;
- efficiency and versatility.
Minuses:
- not stable enough, requires supervision during use.
Review from a real buyer:
I took this heater purely out of interest, it’s the first time I’ve seen such a “Cheburashka”. It turned out to be an excellent thing: it costs little money, there is little gas, it does not burn oxygen at all. In short, if it weren’t for the funny look, it could be used anywhere, but for the home it’s a nice and useful thing.
Back to TOP 10
Tests
Upon completion of the connection, you need to make sure that all connections are tight. To do this, slowly unscrew the valve on the cylinder. The presence of a characteristic hiss will indicate the serviceability of the gearbox. Next, prepare a solution of water and soap, achieving the formation of thick foam. Using a sponge or shaving brush, apply lather to each joint. If bubbles are detected, carefully tighten it.
The characteristics of the propane-butane mixture are such that its mass exceeds the mass of oxygen. In case of omissions, it begins to accumulate in unventilated spaces, displacing air. Therefore, it is better not to place gas cylinders in the basement.
Similar articles
- What volume of propane-butane mixture is filled into the cylinder?
- Country gas tank: pros and cons
- Methods for insulating gas cylinders when placed outdoors
To come in
Already registered? Sign in here.
There are currently 0 users on the page
There are no users viewing this page.
When repairing roofing coverings, it is often necessary to use hot air and even fire: to melt bitumen, melt the underside of roofing felt, and even solder the edge of a metal sheet. And for this you already need special tools. But why not just set the same roofing felt on fire with a homemade torch if our goal is to melt the bitumen?
The fact is that you won't succeed this way. How do you direct the fire in the right direction, especially when there is wind? And how long will such torches last, since the work of laying the roof will be serious? These two main functions are performed by a gas burner. And now we’ll tell you how to choose it.
