Functional and practical water convectors are used if you need to create an effective and economical heating system in any room. Such equipment is reliable; it can work for decades without the slightest problem. However, to feel the benefits, you need to know the rules for choosing devices. Do you agree?
You will learn everything about choosing water-type convectors for the construction or modernization of heating systems from the article we presented. We described in detail the specifics of the convector type of heating and listed the existing types of equipment. They provided criteria on the basis of which you can make an informed choice.
How do convectors heat?
All water heating devices are traditionally designed to heat all kinds of rooms using convection - this is a physical phenomenon in which heated air rises upward, and cold masses take its place.
This process occurs continuously until the temperature equalizes in all layers of some closed volume. To ensure maximum efficiency, convectors have a special design.
They consist of the following elements:
- a pipe through which the coolant flows (this is what hot water is called);
- heat exchanger, which is metal plates (fins) placed on a pipe.
All main parts are covered with a casing; special slots (grid) allow air to circulate freely. This part of the device is designed without sharp corners or protruding parts to prevent injury.
Principle of operation
The very word “convector” indicates that the principle of its operation is based on such a physical phenomenon as convection. Cold air, being more dense, is located in the lower layers - near the floor of the room. Having passed through the convector, the air warms up, its density decreases, as a result of which it rises.
Convection can be not only natural, but also forced. The built-in fan will help increase the convection air flow and thereby increase the efficiency of the heating device.
Classification of water convectors
Modern water convectors for heating are divided into types, indicating technical characteristics. Moreover, it is not difficult to understand all the features, since they differ in only two parameters: the type of convection and the installation method.
For water-type heating devices, convection can be:
- forced;
- natural.
All natural convection equipment has lower power, lower cost and is suitable for heating a variety of small rooms with low ceilings.
In addition, it is often used as an auxiliary heating system for large premises, such as shops, or with a significant area of glazing. To solve these problems, convectors are installed near doorways and windows.
Wall-mounted convector with natural convection is the most popular type for installation in living rooms and offices
The presence of a forced convention means that the heating device is equipped with a fan, which accelerates the air circulation process, and, consequently, the rate of its heating, which ensures rapid heating of even large retail and industrial premises.
Products of this type are also successfully used for heating restaurants, offices, swimming pools and various housing with complex configurations. They create an effective heating system in cases where this is difficult to do with other types of equipment, for example, when installing traditional radiators.
Additionally, convectors are divided according to installation method. In this case, the following types are distinguished:
- wall-mounted, recently a variety of them is often used - ceiling-mounted fixtures;
- floor;
- built into the floor, sometimes the equipment is mounted instead of baseboards.
In any case, the products can be used as part of centralized and autonomous heating systems, and the coolant is exclusively liquid. And also every modern device can be used in the main or auxiliary network.
Can be used for room cooling
A convector can be called universal climate control equipment, since it can perform different tasks in different seasons: heating in winter, cooling in summer. True, not every device is adapted for cooling; manufacturers usually indicate that one or another of their models has this capability.
It should be borne in mind that convectors generate cold much worse than heat, so when calculating the power of the device, you need to rely on your needs for cold, because reducing the heating power, as you now know, is not difficult.
In order for your convector to start cooling, rather than heating, the air in the room, you need to empty it, fill it with a special liquid and connect it to the chiller. However, there are models in which the process of transition from one mode to another is much simpler and faster. They have two unconnected circuits at once: one for the coolant, the other for the refrigerant. To change the operating mode, you will only need to turn off the fluid circulation in one circuit and turn it on in the other.
And a couple more comments regarding the possibility of using this type of climate control equipment for cooling a room. Remembering the principle of operation of a convector, you will understand that in natural mode it is not able to work for cooling. That is why all models designed to operate in two modes are equipped with fans. In addition, the fan helps reduce the amount of condensate formed on the heat exchanger when the convector is operating for cooling.
Existing types of equipment
In addition to the function of fully heating the room, additional convectors are often installed near places where a comfortable microclimate is especially important, for example, near a crib.
Additional equipment must be switched on when the main heating devices cannot cope with timely heating of the air. This situation can arise due to severe frosts or poor quality work of public utilities.
Features of wall models
The most popular are wall convectors. There are several reasons for this - they are affordable in cost and easy to install. And such equipment can be placed anywhere.
The floor-standing type of convector can be installed anywhere in the room to provide comfortable conditions in the selected area
This opportunity is provided by low weight, which allows you to mount equipment even on lightweight partitions, and a large assortment of models. Most often, such a product is designed for heating using natural convection.
For more efficient operation, devices are often equipped with casings that have air channels directed in the right direction, which significantly increases productivity and heating speed.
Description of floor-standing convectors
Floor-standing units are used to heat objects where installation of wall-mounted models is not possible, for example, when glazing starts from the floor level, or large areas need to be heated in industrial buildings.
Often, products belonging to the class of floor-standing water convectors are equipped with fans, which increases productivity and heating speed, but makes the operation somewhat noisy.
A water-type floor convector is easy to install, but takes up useful space. This should be remembered at the stage of choosing a suitable model.
Built-in heating products
The so-called floor-recessed models will fit into any interior. They do not take up useful space and can heat a room of any size.
But the installation of such equipment is the most expensive, the reason: this procedure requires a niche in which the convector is installed. To attach it, you must first make a floor screed or install a reliable raised floor.
If the model is not equipped with a fan, thermal insulation must be used. This will eliminate the loss of heat that will go to heating the floor. If we neglect this requirement, the efficiency of the device will become an order of magnitude lower.
There is another important feature: a sufficient amount of dust accumulates in the casing of such devices, and quickly, which needs to be eliminated, but this is not difficult to do.
Additional advantages of built-in equipment are the longest service life among all types and a variety of standard sizes. High decorative qualities are considered an important advantage. Although the device itself is located in a niche, the protective grille is clearly visible against the background of the floor, so it is given all sorts of colors and shades.
The water convector is an effective thermal barrier and can serve as an elegant interior detail
Still, it is worth remembering that it is more convenient to install such devices during renovation or construction of a building. Since special dismantling of floors for laying pipes and installing in-floor products will be an expensive pleasure.
Let's sum it up
Wall-mounted heating convectors have the simplest possible design, which is determined by the action of a heat exchanger enclosed inside the casing with circulating hot water .
Depending on the manufacturer, the number of heat exchangers may vary, which affects the power of the heating device.
The heating level depends on the location and number of fins . In addition, the design involves equipping it with an air vent and a valve that regulates the water supply.
To perform high-quality and durable heating, it is advisable to use the services of qualified specialists at the installation stage, who will carry out all work in accordance with standards and technology.
Wall-mounted water heating convectors in detail: selection and installation Wall-mounted water heating convectors are very compact structures that can be placed even with very low window sills.
Advantages of convectors over radiators
Although residents of the CIS, for the most part, out of habit, use traditional cast-iron radiators or more modern bimetallic radiators for heating any premises, this trend is now changing. Convectors have a list of significant advantages, which makes them a more practical solution in a number of situations.
Their main advantages are:
- Economical - to heat identical rooms, such devices spend only a quarter of the thermal energy that radiators need.
- High efficiency - in many cases, the products are capable of providing full heating of all kinds of rooms at a coolant (water) temperature of 50°C. According to the standards, conventional radiators at the specified water temperature can heat the room well when it is only 5 °C outside, and at -5 °C it will be necessary to heat the coolant to 78 °C.
- Rapid heating of rooms - thanks to the convention, heating of any room occurs an order of magnitude faster than when heating with radiators. Because they simply emit heat. In addition, the speed of heat propagation is facilitated by the rapid heating of the heat exchanger (pipes, fins). For example, such a procedure with these devices occurs many times more quickly than with cast iron products that are familiar to everyone.
In addition, all convectors are easy to maintain, light weight, compact, and are famous for their high fire safety. Our recommended article will help you get an idea of the advantages of a convector compared to a fan heater.
Their only source of possible danger may be the fan. But it is not installed on all models, and is also low-voltage. Such equipment rarely becomes a source of trouble. The surface of its casing is always cool, which will prevent burns.
Convectors are increasingly used in apartments as main or additional heating devices. In the photo, the built-in device serves as a thermal barrier at the entrance to the balcony
The product is not without its shortcomings, but the list of them is quite short. Thus, the convention creates air currents that contribute to greater dustiness in the premises.
And moving air masses can create a slight draft. This phenomenon is not critical, but undesirable for people suffering from various types of colds. These disadvantages are compensated by an important advantage - convectors never dry out the air.
The biggest disadvantage is the uneven heating of rooms with very high ceilings. The reason lies in the fact that under the influence of the convention, warm air accumulates under the ceilings, and can only descend when cooled, which does not contribute to creating a comfortable temperature.
The same situation will arise if the heated room has moderate-height ceilings, but forced ventilation is used simultaneously with heating.
What is convection
Convective heating uses the simplest laws of physics, according to which heated air becomes lighter and rises. Every heating convector is built on this principle, regardless of what it is powered from. As practice shows, this scheme is highly effective - residential premises become warm, and relatively quickly .
Convector heating allows you to heat rooms for any purpose - these can be living rooms, children's rooms, corridors and foyers, kitchen areas, bathrooms and toilets, covered balconies and loggias. It heats using heated air, quickly saturating the heated rooms with heat. Let's see how the warming up process occurs:
All convectors work on the same principle - they create air circulation in the room, gradually warming it up.
- Possessing a large working surface area, the heating element heats the air around it;
- Warm air masses rise upward, leaving the equipment (or simply going upward if convector-type heating radiators are used);
- Cold air masses replace the air that has gone up.
The process is repeated until convector heating warms up all the air in the rooms.
Heating elements can be powered by electricity or by burning gas fuel. Convector-type heating batteries operate due to the coolant entering them. By the way, the batteries do not have housings, unlike the same electric and gas convectors. But their operating principle is similar - heating is carried out due to the heating air, and the thermal radiation from them is very weak.
How to make the right choice?
To get the expected result, a potential buyer must find out whether it is possible to install convectors in the selected room. It is necessary to take into account whether forced ventilation will be used to create the desired microclimate and whether the ceiling height is acceptable.
You should also make sure that it is technologically possible to supply the necessary equipment. For example, in many cases it is not practical to place built-in devices in residential premises due to the complexity of installation.
Power calculation is a mandatory procedure
If convectors can be installed indoors, the power needs to be calculated. This procedure cannot be ignored - otherwise it will be impossible to create the desired microclimate. That is, it will not heat a home, office or any other object. Another extreme is often encountered - heat, which also will not please the buyer.
To perform the calculation yourself, the following formula is suitable: for every 10 square meters of any room there must be at least a kilowatt of thermal power. But you need to understand that not everything is so simple - this formula will only allow you to determine the average value.
The design of water convectors is simple and reliable, which ensures their service life for decades
Water convectors should be selected with a twenty percent reserve. Better yet, invite a specialist who will carry out an accurate calculation taking into account the heat losses of the building and room. That is, all the features of the object to be heated will be taken into account. This includes glazing area, ceiling height, etc.
The specialist will also be able to indicate the exact location of the devices and suggest where it is best to install additional equipment.
Material of manufacture is always important
When choosing, you should pay attention to the material of manufacture - it affects efficiency, cost, durability and even decorative qualities. Moreover, the last point has become one of the most important today.
For example, devices can be:
- steel;
- aluminum;
- bimetallic - in this case, two types of metals are used for manufacturing.
Copper is also often used. Bimetallic and aluminum devices are considered the most effective today. But steel devices also have a significant advantage - their cost is the most affordable.
The built-in convector can fit perfectly into any interior thanks to the rich color palette available from most equipment manufacturers
It is worth paying attention to the decorative elements of the equipment; they can be different: metal, wood. And for painting, powder paints of various colors are used, which makes the offer even more diverse.
What else to pay attention to
Each heating system (centralized, autonomous) has an operating pressure, in addition, there is another characteristic - test pressure, so convectors must be purchased taking into account such values.
Particular attention should be paid to the test pressure, the reason: it is an order of magnitude greater than the working pressure. The important point is that in different systems such characteristics vary significantly.
For example, old Khrushchev systems are tested under pressure of 5-7 atmospheres. This parameter in new building systems when testing performance can reach an impressive 12-15 atmospheres. Accordingly, the capabilities of convectors must meet the specified values.
If this is not provided for, then damage to the equipment cannot be avoided. As a result, you will have to spend money on buying a new one, repairing a heated room, and in the worst case, compensating for damage to neighbors.
Operating temperature and dimensions
You should also pay attention to the maximum coolant temperature that the convector can withstand. For example, if an autonomous heating boiler is capable of heating water to 95 °C, then there is no need to buy products that can only operate at 70 °C.
An important characteristic is the size of the devices, and their correct selection will allow you to heat the room more efficiently, avoid glass fogging and other problems. For convenience, the industry produces convectors of different depths, lengths, and heights.
The equipment can also be vertical or horizontal, which allows it to be placed almost anywhere, but the buyer must decide on the size.
The size of the convector can be any, the main thing is to choose it correctly, otherwise installation will be difficult
Shut-off valves and thermostats will increase efficiency and create the most comfortable microclimate. This equipment allows you to turn off part of the device at high temperatures in a heated room. Moreover, this happens in automatic or manual mode. But there is also a drawback: all kinds of additional equipment can significantly increase the cost of the product itself.
How not to get confused by technical specifications?
Although all manufacturers include passports with their devices, which indicate their names and power, people often make mistakes in their choice. The reason lies in the fact that an entire line of products consisting of several dozen products can be sold under almost the same abbreviation.
A clear confirmation of this is the family of popular convectors KSK-20, where more than 40 units are produced under the same name, differing only in size.
Moreover, there are products of the same size, in which the plates (ribs) intended for heat exchange are placed at a greater distance from each other, and this significantly reduces productivity. And such subtleties sometimes confuse potential buyers, who may make the wrong choice in the variety of products.
You also need to remember that devices of the same power and size can be flow-through or end-of-line. Convectors belonging to the first option can operate in any heating systems (autonomous, centralized), and products classified in the second group are built only into autonomous systems.
All of the above indicates that the buyer will need some theoretical knowledge to make the right choice.
Basic requirements for the device housing
The appearance of the metal case does not play an important role, since it is located in the floor of the room. Particular attention should be paid to the quality of this element, since the reliability and durability of the heating unit depends on the indicator and its class is determined.
The metal from which the body is made plays an important role:
- For installation in damp rooms, a convector with a body made of stainless material with increased moisture resistance is suitable.
- For dry rooms, select a device with a body made of galvanized or black steel, which is coated with anti-corrosion paint, resistant to external influences.
Typically, special powder compositions are used to coat the metal body. They effectively protect metal from rust formation and external influences.
Designers recommend choosing convectors whose parts and inner walls of the housing are painted in a dark color. They are almost invisible, so they look more aesthetically pleasing
Review of popular models
The market offers an impressive number of models of all types of convectors from various manufacturers. Moreover, domestic companies are actively operating in this area. For example, in the niche of inexpensive heating equipment they are traditional leaders.
So, if the buyer needs reliable, affordable wall-mounted devices, then he should buy the KSK-20 products, proven by time and a large number of users, which are produced by the famous Tolyatti plant. He has been making popular and inexpensive heating units for decades.
The KSK-20 convector is an efficient, reliable and inexpensive heating device
These convectors can cover the needs of all categories of users, as they come in different capacities, sizes, and configurations. For example, the length of the devices is in the range of 60-160 cm, and the weight starts from an insignificant 8 kg, which allows you to place the devices on any walls or partitions without the risk of damage.
The power of such heating equipment ranges from 0.4-2 kW, which allows you to heat both a small living room and a large industrial or commercial premises. High-quality steel is used for manufacturing, which ensures the device has a service life of at least 25 years.
Such convectors can be used in any heating systems, because they can withstand exposure temperatures of up to 150 °C and operating pressures of up to 10 atmospheres. The high-quality powder paint that covers all products protects the device from minor damage and gives it a modern, pleasing appearance.
The only minor drawback of the KSK-20 is the absence of brackets in the kit that are used to attach it to a wall or other vertical surface. Some buyers pay attention to the poverty of the color palette - heating equipment, most often, can only be purchased in traditional white or gray colors, so it does not always fit perfectly into the interior.
If you need a more beautiful device, then you should turn to the product line of another domestic manufacturer - Techno. Thus, at his Moscow plant, various colors are used for decoration and products are decorated with various structural elements. For example, the Vita Bench KBZ model is in demand among buyers.
Its main feature is execution. The floor-standing unit is a bench, and the wooden elements can even be made from popular and valuable types of wood, which makes it a decoration.
At the same time, Vita Bench is a durable and efficient convector, which the manufacturer equips with a thermostatic valve. But the disadvantage of the presented model is the price - it is significantly higher than the KSK-20, which is similar in power.
Covectors can have decorative qualities and serve as decoration in hotels, offices, and homes.
In recent years, another Russian manufacturer of convectors has become known - Varmann. Reason: its products are distinguished by functionality, practicality, and high decorative qualities.
Thus, its line of built-in Qterm HK devices is equipped with air channels and tangential fans that allow air to be drawn only from the desired side. This function significantly increases efficiency and economy.
The fan speed is regulated by a microprocessor, and if necessary, the convector can be connected to a smart home system or using a control panel. The reason for this is simple - thermal power depends on the fan performance
High-quality materials used in manufacturing make it possible to withstand impressive pressure during the pressure testing period, reaching up to 16 atmospheres, and work stably with coolant heated to 90 °C.
The following article, dedicated to this interesting issue, will introduce you to guidelines for choosing a convector-type heater.
Conclusions and useful video on the topic
In this material, a specialist shares information on how to calculate the power of heating devices:
This video clearly shows how to install built-in convectors and what should be taken into account:
Convectors are a profitable and practical alternative to conventional radiators and, no less important, affordable. But the buyer must understand that the possibility of creating a comfortable microclimate in a home, office or workplace depends on his choice, which can be made with theoretical knowledge about heating devices.
If you don’t want to waste time getting them, then you can turn to specialists, this will help you avoid useless financial expenses.
We will be glad to read your story about choosing a water convector. Share the criteria based on which you personally made the purchase. Please leave comments in the block below, ask questions, post photos on the topic of the article.
Installation features
To install batteries in the floor, you need to prepare a place for future batteries and provide free access to the structures for their further maintenance. It is better to entrust such work to professionals, since the slightest mistake can cost a new floor covering.
In this regard, both the built-in batteries and the “warm floor” system are, in principle, the same in terms of the volume of work performed and complexity. Therefore, it is worth focusing on the personal preferences of residents: if they want more heat, localized in one place, it is better to make batteries under the grille. If you need heat that is not so intense, but diffused throughout the room, it is worth installing a “warm floor”.
By the way, the latter can be not only electric. Some home owners, even before rough finishing the floor, connect thin pipes to the water heating system and install them throughout the floor. Next comes screed and finishing.
Battery built into the floor near the windows Source carrera.in.ua
